Yakar 301, Руководство по эксплуатации, Страница: 6 / 14

2 - CENTRAL
HEATING STOVE with FIREPLACE
AND
ITS SPARE PARTS
2.1 Central Heating Stove
must
be placed in the house because it also provides convection from its
surrounding. It can also be installed in a room or in the kitchen having good draft. It is compulsory
to use open expansion boiler.
2.2 Central Heating Stove can not be installed in the bedroom or outside of the house.
2.3 Chimney must be cleaned well before applying stove pipes.
2.4 Attention must
be paid
so that the pipes of the stove get
linked
to each other in good order and one
within the
other.
2.5 Bad quality of the chimney draft affects the output of the stove and at the same time, it can also cause
harmful results for the health.
2.6
Central heating installation must be done by
the authorized
installer by taking installation's connection
diagram into consideration.
2.7 Draft of the chimney must be well and powerful. This particularity can be tested by approximating the
flame to the chimney and it can also be done with a piece of paper. In this case, piece of paper is
pressed to the opening of the chimney and is the piece of paper remains suspended, it means that
the draft of the chimney is good.
2.8
In
order to prevent the backfire of the chimney, "chimney cap" which turns with the wind must be
applied
on the exit
of the chimney.
2.9 Gas warning detector must be applied in the place where Central Heating Stove takes place.
2.10 Installation must be done by being in compliance with the connection diagram taking place in Figure-2.
2.11 For the circumstances when it is required to dismantle Central Heating Stove, its connection must
be done to the installation with "conic pipe couplings".
2.12 Steam exit taking place on the expansion tank must be extended to restroom-bathroom or to ventilation
medium.
2.13 Main line pipes of the installation must be R1" (one finger). Horizontal pipes for the final cores are
selected
as R 3/4".
2.14 Very good heat
insulation must be done for
the pipes passing from the concrete floor. Otherwise,
adequate heat
can not be obtained from
the
cores.
2.15 One or two pipe bend(s) 2 meters of pipe is ideal.
2.16 A strong stove tray, capable of carrying the weight and heat resistant for Central Heating Stove, must
be placed under. Distance of Central
Heating Stove from the wall must be 40 cm.
2.17 Air supply is automatically done with chain driven thermostatic regulator.
2.18 Chimney of the device can not be used together with another device. Chimney type is independent
and it is not suitable for collective usage.
2.19 Ash taking place in the top cleaning lid (Figure
-
1/11) must be controlled once in a month. If needed,
it must be cleaned with the rake.
2.20 Mounting of Central Heating Stove to its place is as explained below.
2.21 In models having chain driven
thermostatic
regulator (Figure
-
2/6), adjustment of
the heat
is done
with the numeric values taking place on it.
2.22 Elimination of extreme heat: if electricity cut off occurs, by-pass valve (Figure 4/4) must be opened.
In models having chain driven thermostatic regulator, bottom air-inlet duct will be closed and burning
will be decreased.
MOUNTING INSTRUCTIONS: This device must be mounted by being in compliance with entire
domestic (national) legislation and related national and European Standards.
Type of Device
Nominal Heat Power (kw)
Area Heating Power (kw))
Water Heating Power (kw)) :
Mass of the device (kg)
301
25
20
22
150
Highest
Water
Operating
Pressure
(bar)
:
1,2
302
25
20
22
120
1,2
401
25
20
175
1,2
303
25
20
22
75
1,2