Yaesu VX-8DR страница 154 Скачать руководство пользователя

Страница: 154 / 176

VX-8DR O

PERATING

ANUAL

152

ODE

TEM

58: MESSAGE REGISTER

Function

: Selects your Personal ID for the Message feature.

See page 104 for details.

ODE

TEM

59: MESSAGE SELECT

Function

: Programming a Message for the Message feature.

See page 102 for details.

ODE

TEM

60: MIC GAIN

Function

: Adjusts the microphone gain level.

Available Values

: LEVEL 1 ~ LEVEL 9

Default

: LEVEL 5

ODE

TEM

61: MONI/T-CALL

Function

: Selects the

MONI

key (just below the

PTT

switch) function.

Available Values

: MONI/T-CALL

Default

: Depends on the transceiver version.

MONI:

Pressing the

MONI

key causes the Noise/Tone Squelch to be over-ridden, al-

lowing you to listen for weak (or non-encoded) signals.

T-CALL: Pressing the

MONI

key activates a 1750-Hz burst tone, used for repeater access

in many countries.

ODE

TEM

62: MUTE

Function

: Adjusts the receiver audio output level when the MUTE function was acti-

vated.

Available Values

: MUTE 30%, MUTE 50%, MUTE 100%, or OFF

Default

: OFF

ODE

TEM

63: OFF TIMER

Function

: Set the OFF Timer time.

The OFF Timer turns the radio off at the programmed time. See page 128 for details.

ODE

TEM

64: ON TIMER

Function

: Set the ON Timer time.

The ON Timer turns the radio on at the programmed time. See page 128 for details.

ODE

ELECTION

ETAILS

Содержание VX-8DR

















































































































































































Результаты поиска

Содержание VX-8DR

Отзывы:

Похожие инструкции для VX-8DR

Бренды по названию

Популярные бренды

Yaesu VX-8DR, Руководство пользователя

Результаты поиска

Содержание VX-8DR

Отзывы:

Похожие инструкции для VX-8DR

Бренды по названию

Популярные бренды