Yaesu VX-8DR страница 45 Скачать руководство пользователя

Страница: 45 / 176

VX-8DR O

PERATING

ANUAL

CTCSS/DCS/EPCS O

PERATION

ROGRAMMING

THE

SER

ELODY

Three User Beep Memories are provided, allowing you to create unique original beep
tone melodies.

Each User Beep Memory can store up to 64 steps with three octaves (“

” through “

”).

Press and hold the

key for one second to enter the Set Mode.

Rotate the

DIAL

knob to select Set Mode Item

12: BEEP

MELODY

Press the

key briefly to enable adjustment of this Set

Mode Item.

Rotate the

DIAL

knob to select the memory slot into which

you wish to store your programmed beep melody. Avail-
able selections are

, and

. The previously stored beep

melody will be displayed.

Press the

key to enable programming the beep melody.

Press and hold the

key for one second to clear any

previous beep melody, if desired.

Rotate the

DIAL

knob to select the first beep tone of the

User Beep Melody. Available selections are

, and

POS

(rest).

Press the

key, then rotate the

DIAL

knob to set the

length of the first beep tone. Available selections are

10ms

(10 msec) -

2500ms

(2.5 sec).

Press the

key to accept the first beep tone of the User

Beep Melody.

If you make a mistake, press the

key to back-space the

cursor, then re-enter the correct beep tone or length.

10. Repeat steps 6 - 9 until you have completed the User Beep

Melody.

11. When there is a beep tone, which you wish to delete, bring

the cursor to that beep tone using the

key, then

press the

key repeatedly until the “

SELECT

” notation in

the “Operation Mode” slot turns into “

DELETE

”. Now, press

and hold in the

key for one second to delete that beep tone.

CTCSS/DCS/EPCS B

ELL

PERATION

Step

Operation Mode

Memory Slot

Tone Length

Beep Tone

Содержание VX-8DR

















































































































































































Результаты поиска

Содержание VX-8DR

Отзывы:

Похожие инструкции для VX-8DR

Бренды по названию

Популярные бренды

Yaesu VX-8DR, Руководство пользователя

Результаты поиска

Содержание VX-8DR

Отзывы:

Похожие инструкции для VX-8DR

Бренды по названию

Популярные бренды