Yaesu VX-8DR страница 171 Скачать руководство пользователя | Manualshive

Страница: 171 / 176

background image

VX-8DR O

PERATING

M

ANUAL

169

S

PECIFICATIONS

T

RANSMITTER

RF Power Output

:

50/144/430 MHz

1.0 W (@4.5 V: AA x 3)
5.0 W (@7.4 V or EXT DC)

50 MHz AM

1.0 W (Fixed)

222 MHz (USA only) 0.5 W (@4.5 V: AA x 3)

1.5 W (@7.4 V or EXT DC)

L3: 2.5 W, L2: 1 W, L1: 0.05 W (@7.4 V, 50/144/430 MHz)
L3: 1 W, L2: 0.5 W, L1: 0.05 W (@7.4 V, 222 MHz)

Modulation Type

:

F2E, F3E: Variable Reactance
A3E: Low Level Amplitude Modulation (50 MHz only)

Maximum Deviation

:

±5 kHz (F2E/F3E)

Spurious Emission

:

At least 60 dB below (@ TX power HI/L3)
At least 50 dB below (@ TX power L2/L1)

Microphone Impedance

: 2K Ohms

R

ECEIVER

Circuit Type

:

NFM, AM:

Double-Conversion Superheterodyne

WFM:

Triple-Conversion Superheterodyne

AM/FM Radio: Single-Conversion Superheterodyne

IF

:

NFM, AM

1st:

47.25 MHz (A (Main) Band),
46.35 MHz (B (Sub) Band),

2nd: 450 kHz

WFM

1st: 45.8 MHz, 2nd: 10.7 MHz, 3rd: 1 MHz

AM/FM Radio: 130 kHz

Sensitivity

:

3.0 µV for 10 dB S/N (0.5-30 MHz @AM)

(A (Main) Band)

0.35 µV (TYP) for 12 dB SINAD (30-54 MHz @NFM)
1.0 µV (TYP) for 12 dB SINAD (54-76 MHz @NFM)
1.0 µV (TYP) for 12 dB SINAD (54-59 MHz @NFM, USA Version)
1.5 µV (TYP) for 12 dB SINAD (76-108 MHz @WFM)
1.5 µV (TYP) for 12 dB SINAD (59-108 MHz @WFM)
1.5 µV (TYP) for 10 dB SN (108-137 MHz @AM)
0.2 µV for 12 dB SINAD (137-140 MHz @NFM)
0.16 µV for 12 dB SINAD (140-150 MHz @NFM)
0.2 µV for 12 dB SINAD (150-174 MHz @NFM)
1.0 µV for 12 dB SINAD (174-222 MHz @WFM)
0.5 µV for 12 dB SINAD (300-350 MHz @NFM)
0.2 µV for 12 dB SINAD (350-400 MHz @NFM)
0.18 µV for 12 dB SINAD (400-470 MHz @NFM)
1.5 µV for 12 dB SINAD (470-540 MHz @WFM)
3.0 µV (TYP) for 12 dB SINAD (540-800 MHz @WFM)
1.5 µV (TYP) for 12 dB SINAD (800-999.90 MHz @NFM)

(Cellular Blocked)

Sensitivity

:

0.18 µV(TYP) for 12 dB SINAD (50-54 MHz @NFM)

(B (Sub) Band)

0.18 µV for 12 dB SINAD (144-148 MHz @NFM)
0.2 µV for 12 dB SINAD (430-450 MHz @NFM)

Selectivity

:

12 kHz/35 kHz (–6dB/–60dB: NFM, AM)
200 kHz/300 kHz (–6dB/–20dB: WFM)

AF Output

:

200 mW @ 8 Ohms for 10 % THD (@ 7.4 V DC)
400 mW @ 8 Ohms for 10 % THD (@ 13.8 V DC)

Specifications are subject to change without notice, and are guaranteed within the 50/144/222/
430 MHz amateur bands only.

Cellular Blocked per FCC rule Part 15.121, may not receive 900 MHz Amateur band.

«
...
169
170
171
172
173
...
»

Содержание VX-8DR

















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VX-8DR

Бренд: Yaesu Страницы: 47

Бренд: Icom Страницы: 47

Бренд: Shure Страницы: 24

JLT-6000 series

Бренд: Jogler Страницы: 16

Бренд: Minebea Intec Страницы: 96

Бренд: Nextech Страницы: 16

Бренд: Williams Sound Страницы: 8

Бренд: SEIKAKU TECHNICAL GROUP Страницы: 6

Бренд: M-system Страницы: 3

My First Transceiver MFT-40

Бренд: EA3GCY Страницы: 29

Бренд: Kramer Страницы: 17

Бренд: Farpointe Data Страницы: 2

Бренд: Honeywell Страницы: 4

Бренд: Honeywell Страницы: 8

Бренд: Honeywell Страницы: 2

Бренд: Honeywell Страницы: 16

Бренд: Honeywell Страницы: 2

ADEMCO 5881EN Series

Бренд: Honeywell Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды