Yaesu MARK-V FT-100MP, Руководство по эксплуатации

Страница: 26 / 120

Page 24
O
PERATING
M
ANUAL
EDSP Filters
(A) APF
Selects and indicates the bandwidth for the EDSP
CW audio peaking filter. Pressing the [ APF
] switch se-
lects the bandwidth to be used for the EDSP CW audio
peaking filter, with available selections of
240 (Hz)/
120 (Hz)/ 60 (Hz)/ DATA ( DATA is an optimized bandwidth
for FAX, PACKET or SSTV operation, user-optimized
via the Menu), or “
OFF ,” and the indicator changes ac-
cording to the bandwidth selected. The most narrow
setting is highly useful for very-weak-signal CW work.
(B) NR
Selects and indicates the setting of the EDSP
Noise Reduction feature. Pressing the [ NR
] switch se-
lects one of four EDSP noise reduction settings, and
the indicator changes according to the selection cho-
sen (choose the selection providing the most effective
reduction of noise under current operating conditions).
(C) CONTOUR
Press one of these four switches to select the de-
sired EDSP (C
ONTOUR
) filter.
: Low Cut Filter ( High-frequency emphasis )
Pressing this button activates the EDSP Low Cut
Filter; the
CONTOUR LED will glow green .
:Mid Cut Filter ( High- & Low-frequency emphasis )
Pressing this button activates the EDSP Medium
Cut Filter; the
CONTOUR LED will glow orange .
: High Cut Filter ( Low-frequencies emphasis )
Pressing this button activates the EDSP High Cut
Filter; the
CONTOUR LED will glow red .
OFF:
EDSP filter is off; the
CONTOUR LED will go out .
ANT [A/B RX] Buttons
[
A/B
] - Pressing this selects either the
ANT A or B
jack on the rear panel, and allows conve-
nient antenna switching at the press of a
button. The selected antenna jack is also
indicated at the top of the display (above
the channel group number).
[
RX
] - Normally, the antenna connected to the
ANT
A or B jack is used for receive (and always
used for transmitting). When this switch is
pressed (display indicator on), an antenna
connected to the
RX ANT IN jack is used
during receive.
MODE Selection Buttons
These momentary buttons select the operating
mode, indicated by the LED in each button. Pressing
AM, CW, RTTY, or PKT multiple times will switch be-
tween the alternate operating features that can be used
by these modes (covered later). Also, when you press
and hold in the [
PKT
] key for one second, the user-
programmed custom function setting mode will be ac-
tivated.
F
RONT
P
ANEL
C
ONTROLS
KEY
MIC
POWER
MOX VOX
METER
IC/SWR
ALC/COMP
VCC/MIC
A
B
PHONES
AGC
MIC
AF
GAIN
RF
GAIN
PROC
FAST 0
6
12
1 8
dB ( )
OFF SLOW
AUTO
ATT
240
120
6 0
A
IPO A/B
ANT
R X
R X MAIN VFO-A TX
RCL
7
3
QMB BAND
STO
DUAL
M A
A B
M CK A M
M GRP
RPT
A B
VFO/
MEM
FAST LOCK
OFF
B
C
D
OFF OFF
APF
APF
NR
LSB
USB
CW
AM
FM
PKT
CLASS-A AF REV SQL SUB S MONI RF PWR MONI SUB AF PROC
NR
1.8
1
1 0
4
2 1
7
SUB
D E
3.5
2
14
5
24.5
8
29
0
18
6
28
9
ENT
DOWN U P
VRF IDBT
EDSP