Yaesu MARK-V FT-100MP, Руководство по эксплуатации, Страница: 63 / 120

Page 61
O
PERATING
M
ANUAL
Operation
Balance - The AF GAIN knob adjusts the volume
for both the Main and Sub VFOs simultaneously. The
small
SUB AF now functions as a “balance” control
between Main and Sub audio levels.
Note - To “reverse” Main and Sub receiver audio at
any time, press the [ AF REV
] button just to the left of
the DOWN(
q
)/UP(
p
)
keys so its LED lights. The func-
tions of the AF GAIN and small SUB AF controls are
now switched. Press the button again to return to nor-
mal operation.
Remember that when the Sub VFO is turned off by
pressing [ DUAL
] again, the
AF GAIN control configu-
rations no longer apply.
Using Headphones for Dual Receive
To take advantage of dual reception, you will want
to connect stereo headphones to the PHONES jack.
Like the AF GAIN control, headphone audio mixing can
also be configured as desired from menu selection 4-8 .
Three audio mixing schemes are selectable as follows:
Mono - Audio from both the Main and Sub receiver
is combined equally in both ears (as from the loud-
speaker when headphones are not used).
Stereo 1 - This is a combination of the audio from
the two receivers and it gives you some audio from
each channel in each ear, but with the Main receiver
emphasized in the left ear, and the Sub receiver em-
phasized in the right ear, resulting in a kind of “3-D”
spatial audio effect.
Stereo 2 - Audio from the Main receiver is only heard
in the left ear, and audio from the Sub receiver is heard
only in the right ear.
Note that both the Main and Sub VFOs must be
activated (to put the MARK-V FT-1000MP
Field
into
the dual receive mode), and the AF GAIN control(s)
must be balanced (centered) to hear both receivers.
Compare these two positions with both VFOs tuned to
signals, to select the audio mixing scheme you prefer.
Also observe that the VRF, EDSP, RF GAIN, SHIFT,
WIDTH, NOTCH, and AGC functions do not affect the
sub receiver (AGC is automatically selected according
to mode, or else from
menu selection 8-7 ).
Headphone Audio Adjustments
The Main and Sub receiver audio levels available
from headphone jacks A and B are manually adjust-
able. Underneath the top panel access cover are four
trimpots allowing individual adjustment of Main and Sub
audio for each headphone jack. With a headphone in-
serted into the appropriate jack, you can rotate these
controls using a small insulated screwdriver for opti-
mum level and balance. Refer to the drawing below for
trimpot locations.
U
SING
SUB VFO B
Caution!
Do not adjust VR6812 control in the top access
panel by mistake, as this will adversely affect meter
tuning indication, requiring factory re-alignment!
CW
ALC - UNIT
RTTY
TRV
DLAY
HPB-S
FM MIC VOX PKT A-VOX
HPB-M HPA-M HPA-S
V
R
68
01
V
R
68
10
V
R
6
80
4
V
R
68
07
V
R
6
80
2
V
R
6
81
1
N
O
R
M
TR
V
V
R
68
05
V
R
68
08
V
R
6
80
3
V
R
6
81
2
V
R
68
06
V
R
68
09
J6803 (BLK)
J6804
(BLK) J6802 (BRN)
J6808 (BLU) J6807 (YEL) J6805
(BLU)
J6806
(BLK)
J6809
(PUL)
C6807
C6803
J
6
8
1
1
(Y
E
L
)
J
6
8
1
0
(
B
L
U
)
J6801
(RED)
Headphone B Setting (MAIN RX Level Adjust)
Headphone A Setting (MAIN RX Level Adjust)
Headphone B Setting (SUB RX Level Adjust)
Headphone A Setting (SUB RX Level Adjust)