Yaesu MARK-V FT-100MP, Руководство по эксплуатации, Страница: 34 / 120

Page 32
O
PERATING
M
ANUAL
The following controls are accessible beneath the
removable panel on the top half of the transceiver case.
Push the slide rearward and pry up the lid to expose
the ALC UNIT circuit board and potentiometer controls.
Most control settings are preset at the factory for nor-
mal operation. Should you desire to change a particu-
lar setting, use a small insulated screwdriver to rotate
the desired potentiometer.
TRV
This switch disables the power amplifire of the
MARK-V FT-1000MP
Field
. When you are using the
transverter, move this switch to the “ TRV ” position.
When using the FTV-1000 transverter with the
FRB-5 Relay Unit, however, leave this switch in the
“NORM” position.
CW
This control adjusts the tuning meter segment in-
dications for CW center tuning. It should be adjusted
such that the center segment lights up when your fa-
vorite pitch (as set by the CW
PITCH control and con-
firmed by pressing the [ SPOT
] button) is received.
RTTY
This control adjusts the tuning meter segment in-
dications for RTTY center tuning.
PKT
This control adjusts the tuning meter segment in-
dications for Packet center tuning.
T
OP
P
ANEL
A
CCESS
& C
ONTROLS
A-VOX (ANTI-VOX TRIP)
This control sets the level of negative feedback of
receiver audio to the microphone, to prevent receiver
audio from activating the transmitter (via the micro-
phone) during VOX (voice-actuated transmit/receive
switching) operation. Adjustment is described in the
Operation chapter.
DLAY (VOX Delay)
This control sets the hang time of the VOX circuit,
between the moment you stop speaking, and the auto-
matic switch from transmit back to receive. Adjust this
for smooth VOX so the receiver is only activated when
you want to listen.
VOX
This control sets the gain of the VOX circuit, to set
the level of microphone audio needed to activate the
transmitter during voice operation while the VOX but-
ton on the front panel is depressed.
FM MIC
During FM operation, this control adjusts the mi-
crophone gain (and transmitter deviation). More clock-
wise settings produce a wider bandwidth signal.
NOTE : This control has been preset at the factory
to produce the correct deviation with standard micro-
phone levels. A deviation meter should be connected
for proper readjustment, as it is difficult to determine
the proper setting by ear. Remember that maximum
deviation permitted on HF is ±2.5 kHz.
CW
ALC - UNIT
RTTY
TRV
DLAY
HPB-S
FM MIC VOX PKT A-VOX
HPB-M HPA-M HPA-S
V
R
6
8
0
1
V
R
6
8
1
0
V
R
6
8
0
4
V
R
6
8
0
7
V
R
6
8
0
2
V
R
6
8
1
1
N
O
R
M
T
R
V
V
R
6
8
0
5
V
R
6
8
0
8
V
R
6
8
0
3
V
R
6
8
1
2
V
R
6
8
0
6
V
R
6
8
0
9
J6803 (BLK)
J6804
(BLK) J6802 (BRN)
J6808 (BLU) J6807 (YEL) J6805
(BLU)
J6806
(BLK)
J6809
(PUL)
C6807
C6803
J
6
8
11
(Y
E
L
)
J6
8
1
0
(B
L
U
)
J6801
(RED)