Yaesu FTM-500DR Скачать руководство пользователя страница 73

Страница: 73 / 74

Troubleshooting

Check the following before requesting repair services.

There is no power

•

Is the external power supply connected correctly?

Connect the black wire to the negative (-) terminal and the red wire to the positive (+) terminal.

•

Is the voltage and current capacity of the external power supply sufficient?

Check the voltage and current capacity of the external power supply.

Voltage: 13.8V

Current capacity: 15A or higher

•

Is the fuse blown?

Replace the fuse.

There is no sound

•

Is the squelch level or setting too high?

Adjust the squelch level when receiving weak signals.

•

Is the volume low?

Increase the volume by turning the VOL/SQL knob in the clockwise direction.

•

Is the tone squelch or DCS set to on?

When the tone squelch or DCS is turned on, no sound will be heard until signals

containing the set tone frequency or DCS code corresponding to the set code are

received.

•

Is the C4FM digital mode on?

When the AMS function is on, the sound is not output until the transceiver receives an

Analog FM mode signal. Also, when the DG-ID function is ON, and the DG-ID number

to other than “00”, the sound is not output until the transceiver receives a signal with a

corresponding DG-ID number.

•

Is the external speaker connected?

Properly connect a speaker with an impedance of 4 to 16Ω.

•

Is the Bluetooth

headset in use?

Turn OFF the power of the Bluetooth

headset, or turn OFF the Bluetooth

function in

the setup menu.

There is no transmission

•

Is the PTT button pressed properly?

•

Is the microphone connected correctly?

Plug the connector all the way into the MIC jack.

•

Is the transmit frequency set to the amateur band?

Transmission outside the amateur band is not possible.

•

Is the antenna or co-axial cable broken?

Replace the antenna or co-axial cable.

•

Is the voltage of the external power supply normal?

When the voltage of the power supply drops during transmission, the transceiver may

not run at full performance. Use a stable DC power supply with a voltage of 13.8V and

a current capacity of 15A.

The keys or knobs do not operate

•

Is the lock function activated?

Cancel the lock by briefly pressing the Power switch.

Содержание FTM-500DR











































































Результаты поиска

Содержание FTM-500DR

Отзывы:

Похожие инструкции для FTM-500DR

Бренды по названию

Популярные бренды

Yaesu FTM-500DR, Руководство для продвинутых пользователей

Результаты поиска

Содержание FTM-500DR

Отзывы:

Похожие инструкции для FTM-500DR

Бренды по названию

Популярные бренды