Yaesu FTDX10 страница 91 Скачать руководство пользователя

Страница: 91 / 123

MIC GAIN

Function: Sets the microphone gain for the FM

mode.

Available Values: MCVR / 0 - 100

Default Setting: MCVR

Description:

MCVR: Adjust the microphone gain (0 - 100) us-

ing the front panel [MIC/SPEED] knob.

0 - 100: Fixed to the set value.

REAR SELECT

Function: Selects the input jack of the FM signal.

Available Values: DATA / USB

Default Setting: DATA

Description: Selects the input jack of the FM sig-

nal when “FM MOD SOURCE” is set

to “REAR”.

DATA: Inputs from the RTTY/DATA jack on the

rear panel.

USB: Inputs from the USB jack on the rear pan-

el.

RPORT GAIN

Function: Sets the level of the FM signal input

when “FM MOD SOURCE” is set to

“REAR”.

Available Values: 0 - 100

Default Setting: 50

RPTT SELECT

Function: Sets the PTT control for the FM trans-

mit signal.

Available Values: DAKY / RTS / DTR

Default Setting: DAKY

Description:

DAKY: Controls the FM transmit signal from the

RTTY/DATA jack (pin 3) on the rear panel.

DTR: Controls the FM transmit signal from the

USB virtual COM/DTR ports.

RTS: Controls the FM transmit signal from the

USB virtual COM/RTS ports.

RPT SHIFT(28MHz)

Function: Sets the RPT offset frequency on the

28 MHz band.

Available Values: 0 - 1000 kHz

Default Setting: 100 kHz

Description: The RPT offset frequency can be set

at 10kHz increments between 0kHz

and 1000 kHz.

RPT SHIFT(50MHz)

Function: Sets the RPT offset frequency on the

50 MHz band.

Available Values: 0 - 4000 kHz

Default Setting: 1000kHz

Description: The RPT offset frequency can be set

at 10kHz increments between 0kHz

and 4000kHz.

RPT

Function: Sets the Repeater Shift Direction.

Available Values: - / SIMP / +

Default Setting: SIMP

Description:

Shifts to the lower frequency offset.

SIMP: The frequency does not shift.

Shifts to the higher frequency offset.

TONE FREQ

Function: Setting of the CTCSS Tone Frequency.

Available Values: 50 standard CTCSS tones

Default Setting: 67.0 Hz

ENC/DEC

Function: Selects the Tone Encoder and/or De-

coder mode.

Available Values: OFF / ENC / TSQ

Default Setting: OFF

Description:

ENC: CTCSS Encoder

TSQ: CTCSS Encoder/Decoder

Содержание FTDX10




























































































































Результаты поиска

Содержание FTDX10

Отзывы:

Похожие инструкции для FTDX10

Бренды по названию

Популярные бренды

Yaesu FTDX10, Руководство по эксплуатации

Результаты поиска

Содержание FTDX10

Отзывы:

Похожие инструкции для FTDX10

Бренды по названию

Популярные бренды