Yaesu FTDX10 Скачать руководство пользователя страница 10

Страница: 10 / 123

Installation and Interconnections

Antenna Considerations

The FTDX10 is designed to connect to a 50 Ohm resistive impedance antenna at the Amateur operating

frequencies. Select an appropriate antenna (dipole antenna, YAGI antenna, cubical quad antenna, etc.)

that is suitable for the chosen operation and bands.

Construct the antenna and coaxial cable, or use a suitable antenna tuner, to maintain the impedance

presented to the FTDX10 antenna connector for an SWR of 1.5 or less. Careful preparation of the anten-

na and/or tuner will permit maximum performance, and protect the transceiver from damage.

High transmitter RF voltages may be present on the antenna; install it so it will not be easily touched when

in operation.

Antenna Connections

Carefully follow the illustration regarding the proper connection of antennas and coaxial cables.

To prevent damage from lightning, atmospheric electrical discharges,

electric shock etc., provide a good earth ground.

Use a short, thick, braided cable to connect the station equipment to the

buried ground rod (or alternative earth ground system).

Power Cable Connections

Carefully follow the illustrations regarding the proper connection of the DC power cable.

Use the DC power cable supplied with the FTDX10 to make the power connections to the power supply.

RED

FUSE: 25A

Check the DC voltage and current rating

(+13.8 V, 25 A) of the power supply before

connecting to the transceiver.

DC power cord (supplied)

BLACK

Installation guidelines

•

Ensure adequate ventilation around the trans-

ceiver, to prevent heat build-up and possible re-

duction of performance due over heating.

•

Do not install the transceiver in a mechanically

unstable location, or where objects may fall onto

it from above.

•

To minimize the possibility of interference to

home entertainment devices, take all precaution-

ary steps including separation of TV/FM anten-

nas from Amateur transmitting antennas to the

greatest extent possible. Keep the transmitting

coaxial cables separated from cables connected

to home entertainment devices.

•

The AC Power Cord connected to a socket-out-

let with earthing connection. A socket-outlet with

earthing connection shall connect to protective

earthing conductor.

Содержание FTDX10




























































































































Результаты поиска

Содержание FTDX10

Отзывы:

Yaesu FTDX10, Руководство по эксплуатации, Страница: 10 / 123

Результаты поиска

Содержание FTDX10

Отзывы: