Yaesu FTDX10 Скачать руководство пользователя страница 89

Страница: 89 / 123

AGC SLOW DELAY

Function: Sets the AGC-SLOW DELAY voltage

decay characteristics for AM mode.

Available Values: 20 - 4000msec

Default Setting: 4000msec

Description: Sets the AGC voltage decay char-

acteristics in 20msec steps after the

input signal level becomes lower

than the AGC detection level and the

HOLD time has expired.

LCUT FREQ

Function: Sets the low-frequency cutoff audio fil

ter in AM mode.

Available Values: OFF / 100Hz - 1000Hz

Default Setting: OFF

Description: The cutoff frequency can be set at

50Hz increments between 100Hz

and 1000Hz.

LCUT SLOPE

Function: Sets the slope of the low-frequency

cutoff audio filter in AM mode.

Available Values: 6dB/oct / 18dB/oct

Default Setting: 6dB/oct

HCUT FREQ

Function: Sets the high-frequency cutoff audio

filter in AM mode.

Available Values: 700Hz - 4000Hz / OFF

Default Setting: OFF

Description: The cutoff frequency can be set at

50Hz increments between 700Hz

and 4000Hz.

HCUT SLOPE

Function: Sets the slope of the high-frequency

cutoff audio filter in AM mode.

Available Values: 6dB/oct / 18dB/oct

Default Setting: 6dB/oct

AM OUT LEVEL

Function: Sets the level of the receive AM signal

output from the RTTY/DATA jack.

Available Values: 0 - 100

Default Setting: 50

TX BPF SEL

Function: Selects the audio passband of the DSP

modulator on the AM mode.

Available Values: 50-3050 / 100-2900 / 200-2800

300-2700 / 400-2600 (Hz)

Default Setting: 50-3050 Hz

AM MOD SOURCE

Function: Selects the transmit audio input jack

in the AM mode by pressing the [VOX/

MOX] key.

Available Values: MIC / REAR

Default Setting: MIC

Description:
MIC: Audio is input from the MIC jack on the

front panel.

REAR: Disables the microphone circuit on the

front panel and inputs audio/data from the

USB jack or RTTY/DATA jack on the rear

panel.

MIC GAIN

Function: Sets the microphone gain for the AM

mode.

Available Values: MCVR / 0 - 100

Default Setting: MCVR

Description:
MCVR: Adjust the microphone gain (0 - 100) us-

ing the front panel [MIC/SPEED] knob.

0 - 100: Fixed to the set value.

REAR SELECT

Function: Selects the input jack of the AM signal.

Available Values: DATA / USB

Default Setting: DATA

Description: Selects the input jack of the AM sig-

nal when “AM MOD SOURCE” is set

to “REAR”.

DATA: Inputs from the RTTY/DATA jack on the

rear panel.

USB: Inputs from the USB jack on the rear pan-

el.

RPORT GAIN

Function: Sets the level of the AM signal input

when “AM MOD SOURCE” is set to

“REAR”.

Available Values: 0 - 100

Default Setting: 50

RPTT SELECT

Function: Sets the PTT control for the AM trans-

mit signal.

Available Values: DAKY / RTS / DTR

Default Setting: DAKY

Description:

DAKY: Controls the AM transmit signal from the

RTTY/DATA jack (pin 3) on the rear panel.

DTR: Controls the AM transmit signal from the

USB virtual COM/DTR ports.

RTS: Controls the AM transmit signal from the

USB virtual COM/RTS ports.

Содержание FTDX10




























































































































Результаты поиска

Содержание FTDX10

Отзывы:

Yaesu FTDX10, Руководство по эксплуатации, Страница: 89 / 123

Результаты поиска

Содержание FTDX10

Отзывы: