9
Connecting to a Faraway Station Using WIRES-X
(3)
Connected to the local node, successfully connected
to Internet nodes or rooms (nodes or rooms are the
same as ones previously used)
䢶䢵䢲䢰 䢺䢲 䢲䢢
䣆䣐
䣌䣓䢳䣛䣄䣉䢯䣐䣆䢳䢢䢢䣕䣊䣋䣐䣃䣉䣃䣙
䣌䣃䢴䣛䣕䣑䢯䣐䣆䢴䢢䣐䣃䣉䣑䣛䣃
(4)
Connected to the local node, successfully connected
to Internet nodes or rooms (nodes or rooms are
different from ones previously used)
䢶䢵䢲䢰 䢺䢲䢲䢢
䣆䣐
䣌䣓䢳䣛䣄䣉䢯䣐䣆䢳䢢䣕䣊䣋䣐䣃䣉䣃䣙
䣌 䣃 䢳䣜䣔 䣎 䢯䢹 䢺 䢻䢢䣕䣊䣋䣐䣃䣉䣃䣙
When the is displayed, rotate the
O
. Call signs
of nodes or rooms where you previously established
connection will flash.
䢶䢵䢲䢰 䢺䢲 䢲䢢
䣆䣐
䣌䣓䢳䣛䣄䣉䢯䣐䣆䢳䢢䢢䣕䣊䣋䣐䣃䣉䣃䣙
䣌䣃䢴䣛䣕䣑䢯䣐䣆䢴䢢䣐䣃䣉䣑䣛䣃
Tip
While the [
X] is flashing, press the
%
to re-establish
connection to the local node.
Tip
When any local node cannot be found, [
X
] will disappear
in 5 minutes.
Tip
When the detected local node is a repeater station, [
[
R ]
]
will appear below [
X
].
䢶䢵䢲䢰 䢺䢲 䢲䢢
䣆䣐
䣌䣓䢳䣛䣄䣉䢯䣐䣆䢳䢢䣕䣊䣋䣐䣃䣉䣃䣙
Caution
WIRES-X can be used only on band A.
When using band B (shown on the bottom part of the screen) as the operation band, after
pressing and holding
%
for 1 second or more, band A (shown on the top part of the screen) will
automatically become the operation band.
Connecting to a node or room on the Internet
You can connect to a desired node or room in one of the following ways.
• Selecting an accessible node or room from the list
• Specifying the node name or room name
• Selecting the most recently connected node or room
• Specifying the DTMF ID of the desired node or room
●
Searching from the node & room lists
1
When the connection destination is displayed, press and
hold
H
for 1 second or more.
The menu list of the local node will appear.
䢶䢵䢲䢰 䢺䢲 䢲䢢
䣆䣐
䣌䣓䢳䣛䣄䣉䢯䣐䣆䢳䢢䢢䣕䣊䣋䣐䣃䣉䣃䣙
