Yaesu FT DX 9000D - COMPUTER AIDED TRANSCEIVER, Руководство по эксплуатации

Страница: 136 / 156

Page 134 FT
DX
9000D O
PERATION
M
ANUAL
M
ENU
M
ODE
GENERAL G
ROUP
028. ANT SELECT
Function : Sets the method of antenna selection.
Available Values : BAND/STACK
Default Setting : BAND
BAND: The antenna is selected in accordance with
the operating band.
STACK: The antenna is selected in accordance with
the band stack (different antennas may be
utilized on the same band, if so selected in
the band stack).
029. BEEP LEVEL
Function : Sets the beep level.
Available Values : 0 ~ 255
Default Setting : 50
030. CAT RATE
Function : Sets the transceiver’s computer-interface
circuitry for the CAT baud rate to be used.
Available Values : 4800/9600/38400 bps
Default Setting : 4800 bps
031. MEM GROUP
Function : Enables/Disables Memory Group Opera-
tion.
Available Values : DISABLE/ENABLE
Default Setting : DISABLE
032. QUICK SPLIT FREQ
Function : Selects the tuning offset for the Quick Split
feature.
Available Values : –20 ~ 0 ~ +20 kHz (1 kHz Step)
Default Setting : +5 kHz
033. TIME OUT TIMER
Function : Sets the Time-Out Timer countdown time.
Available Values : OFF/5/10/15/20/25/30 min
Default Setting : OFF
The Time-Out Timer shuts off the transmitter after
continuous transmission of the programmed time.
034. TRV OFFSET
Function : Set the 10’s and 1’s of the MHz digits dis-
play for operation with a transverter.
Available Values : 30 ~ 49 MHz
Default Setting : 44 MHz
If you connect a 430 MHz transverter to the radio, set
this menu to “30” (the “100 MHz” digits are hidden on
this radio).
035. µTUNE DIAL STEP
Function : Select the µ-TUNE mode.
Available Values : DIAL STEP-1/DIAL STEP-2/OFF
Default Setting : DIAL STEP-1
DIAL STEP-1: Activates the µ-TUNE system in the
Auto mode using “ FINE ” steps of the
µ-TUNE knob (1 step/click) on the 14
MHz and lower amateur bands on the
main band (VFO-A).
DIAL STEP-2: Activates the µ-TUNE system in the
Auto mode using “ COARSE ” steps of
the µ-TUNE knob (2 steps/click) on
the 7 MHz and lower amateur bands.
On the 10/14 MHz bands, “FINE” µ-
TUNE knob steps will be used (1 step/
click).
OFF: Disables the µ-TUNE system. Acti-
vates the VRF feature on the 14 MHz
and lower amateur bands on the main
band (VFO-A).
036. MIC SCAN
Function : Enables/disables scanning access via the
microphone’s [ UP
]/[
DWN
] keys (only available at the
rear panel’s MIC Jack).
Available Values : ENABLE/DISABLE
Default Setting : ENABLE
037. MIC SCAN RESUME
Function : Selects the Scan Resume mode.
Available Values: PAUSE/TIME
Default Setting : TIME
PAUSE: The scanner will hold until the signal disap-
pears, then will resume after one second.
TIME: The scanner will hold for five seconds, then
resume whether or not the other station is
still transmitting.
038. AF/RF DIAL SWAP
Function : Reverses the functions of the AF GAIN
(VFO-B) and RF GAIN (VFO-A) knobs.
Available Values : NORMAL/SWAP
Default Setting : NORMAL
When this menu is set to “SWAP,” you may adjust
the sub (VFO-B) receiver audio using the large
RF
GAIN (VFO-A) knob and adjust the main (VFO-A)
receiver RF gain using the small AF GAIN (VFO-B)
knob. This puts both “Volume” controls on the same
shaft.