Page 116
FT
DX
9000D O
PERATION
M
ANUAL
M
EMORY
O
PERATION
1.
Press the MCH/GRP key (#
) momentarily.
The imbedded LED will glow Red, indicating that
you are now ready to view memory channel con-
tents.
Advice
If the Red LED imbedded in the MCH/GRP switch does not
light up, check to be sure that the orange lamp to the right of
the CLAR/VFO-B knob (#
) is not illuminated. It is, press
the A/B switch (#
) to make it go out, then press the MCH/
GRP key again.
2.
Press the A
M key (#
).
The data stored in the currently-selected memory
channel will be displayed in the Sub (VFO-B) band
frequency field. However, since you are only check-
ing the contents of the memory channel, your radio
will not have moved to the memory channel's fre-
quency.
3.
Rotate the CLAR/VFO-B knob to select other
memory channels. To exit from the Memory Check
mode, press the A
M key once more.
E
RASING
M
EMORY
C
HANNEL
D
ATA
1.
Press the MCH/GRP key (#
) momentarily. The
imbedded LED will glow Red, indicating that you are
now ready to view memory channel contents.
Advice
H
If the Red LED imbedded in the MCH/GRP switch does
not light up, check to be sure that the orange lamp to the right
of the CLAR/VFO-B knob (#
) is not illuminated. It is,
press the A/B switch (#
) to make it go out, then press
the MCH/GRP key again.
2.
Press the A
M key (#
).
The data stored in the currently-selected memory chan-
nel will be displayed in the Sub (VFO-B) band fre-
quency field.
3.
Rotate the CLAR/VFO-B knob (#
) to select the
memory channel that you would like to erase.
4.
Press the LOCK switch (#
) to erase the contents
of the selected memory channel.
Advice
After erasure, only the memory channel number will
remain; the frequency data will disappear from the
display.
If you make a mistake and wish to restore the memory’s
contents, just repeat steps (1) through (3) above.
Advice
While the Memory Check function is engaged, the
memory channel number will blink.
While operating in the VFO mode, using Memory
Check, you may store the current contents of the VFO
into the selected memory by pressing and holding in
the A
M key for two seconds (until the double
beep). Conversely, if you wish to write the contents
of the current memory into the Main (VFO-A) regis-
ter, press and hold in the M
A key (#
) for two
seconds.
Checking a Memory Channel’s Status
Before programming a channel into memory, you can check the current contents of that channel without the danger of
over-writing the data accidentally.
CLAR/VFO-B knob
switch
MCH/GRP switch
CLAR/VFO-B knob
switch
LOCK switch
Содержание FT DX 9000D - COMPUTER AIDED TRANSCEIVER
