XYZ Printing PartPro300 xT Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 33

XYZ Printing PartPro300 xT Скачать руководство пользователя страница 32

PartPro300 xT

31

8.5 Clean Up Glass Plate

①

User should always keep the glass plate clean. Any dirt, dust, and oil on your glass plate can affect your print quality.

If the filament adheres poorly to dirty glass, it ccan directly affect the object. Some ways of cleaning the glass are much

more effective than others. For PartPro300xT, the glass surface has a print bed sheet film on it. User should regularly
change the mylar whenever they find wear.

② After removing

print bed sheet

, user should clean the glass thoroughly before replacing a new sheet as following.

1. Wipe down the glass with isopropyl alcohol.

2. Or wash the glass with water (may add mild dish detergent). Rinse thoroughly

Note:

Don’t use any tools that will scratch/score the glass.

9. SUPPORTING INFORMATION

If your printer experiences problems, review the following troubleshooting instructions to resolve the issue. If the issue
persists, contact the customer service center.

9.1 Issue code and troubleshooting

If your printer experiences problems, a relevant service code will be displayed on the printer screen and/or software

interface. Please refer to the following service code description table for initial troubleshooting.

Error Code No.

Failure Description

Print bed heated for too long

Print head heated for too long

Print head 2 heated for

too long

Print bed heated issue--

temperature exceed

Print bed heated issue--

temperature exceed

Print head 2 heated issue--

temperature exceed

Abnormal--X axis

Abnormal--Y axis

Abnormal--Z axis

Internal communication error --

memory error

Print head memory error

Print head not match

User Action

Please reboot or check the print bed heater & thermistor harness connection

(need to open back cover).

Please check the Flexible flat cable and reboot.

Please check the Flexible flat cable and reboot.

Please reboot or check the print bed heater & thermistor harness connection

(need to open back cover).

Please check the Flexible flat cable and reboot.

Please check the Flexible flat cable and reboot.

Check the X axis cable of the motor and the sensor, and check the X axis

position of the sensor.
Check the Y axis cable of the motor and the sensor, and check the Y axis

position of the sensor.
Check the Z axis cable of the motor and the sensor, and check the Z axis

position of the sensor.

Reboot the printer.

Replace the print head.

Replace the print head. (Jr.Pro 40W, other 35W)

0 0 1 0

0 0 1 1

0 0 1 2

0 0 1 3

0 0 1 4

0 0 1 5

0 0 3 0

0 0 3 1

0 0 3 2

0 0 5 0

0 0 5 2

0 0 5 4

«
...
30
31
32
33
»

Содержание PartPro300 xT


































Отзывы:

Нет отзывов