background image

 

 

25

 

CONTACTING TECHNICAL SUPPORT 
For machine parts and technical service in North America, please call: 1-800-793-3523. Please provide serial 

number when calling for service. In Europe, please call: +49 711 8103 0. 
 

PRODUCT WARRANTY  
Xyron, Inc. warrants that the Xyron XM4400 is free from defects in material and workmanship for a period of one (1) 

year from the date of purchase. Xyron, Inc. will repair or replace a defective product or part without charge provided 
it is returned to the address below, freight prepaid with proof of purchase. If the product is damaged by neglect or 

misuse the warranty is null and void.  
 

WARRANTY CAUTION 
The warranty made herein is in lieu of all other warranties, express or implied, including any warranty or 

merchantability or fitness for a particular purpose. Xyron will not be liable for property damage or personal injury 
(unless primarily caused by its negligence), loss of profit or other incidental or consequential damages arising out of 

the use or inability to use the equipment. 
 

EXCLUSIONS TO THE WARRANTY 
This warranty specifically does not cover: 

1. Damage to the laminating rolls caused by knives, razor blades, other sharp objects, or failure caused 
     by adhesives. 

2. Damage to the machine caused by lifting, tilting, and/or any attempt to position the machine other 
      than rolling on the installed casters on even surfaces. 

3. Improper use of the machine. 
 

NOTICE  
The information in this manual is subject to change without notice. Xyron shall not be liable for errors 
contained herein or for incidental or consequential damages in connection with the furnishing, performance or 
use of this material.  
The purchase or acquisition of this product does not confer the right or license to use the machine and cartridges in 

the retro-reflective field or to make or sell machines or cartridges for use in the retro-reflective field.  
 

 
XYRON, INC. , 
8465 N. 90th St., Suite #6, Scottsdale, AZ 85258 
Esselte Leitz GmbH & Co KG, 
Siemensstr. 64, 70469 Stuttgart, Germany 
   

 

 

 

 

 

 

 

   

 

 

 

 

 

 

 

 
   

 

 

 

 

 

 

 

 

 

 

 

 

Содержание XRN4400



























Отзывы: