background image

WQG-10029-01

Act-Pak® Electronic Instrumentation

Models 1100D and 1100DN Quick Guide

Field Adjustments

The Flow Rate Indicator/Totalizer readout modules 
are programmed at the factory and will retain the 
program indefinitely. If it becomes necessary to 
reprogram the module, use the following procedure. 
Before starting to program the readout review the 
complete procedure listed below and determine 
all factors and parameters before starting the 
procedure.

 

t

WARNING!

ELECTRICAL HAZARD Use caution when working with 

disassembled AC electrical components.

To enter the programming mode, depress and hold 
the 

SEL

 button on the readout for 2 seconds. In the 

program mode the display will show 

Pro

 and flash to 

nO

.

There are four (4) programming modules available. 
Press the 

RST

 button to step through the modules.

When the correct module is displayed press the 

SEL

 button to enter that module. In the module, 

the function being programmed is shown then the 
display flashes to the value presently entered for the 
function. Pressing the 

RST

 button stops the display 

from flashing and places the unit into the data 
selection mode.

In the selection mode the operator presses the 

RST

 

button to scroll through the parameters available for 
that menu. When the desired selection is reached, 
press the 

SEL

 button to store the data and advance 

to the next menu.

When setting numerical values use the 

RST

 button 

to increment the flashing digit, and momentarily 
press the 

SEL

 button to advance to the next digit. To 

start the least significant digit flashing momentarily 
depress the 

RST

 button.

To exit the programming mode and save all 
parameters step through the module until one of the 
four main modules is displayed, then press the 

RST

 

button until Pro nO displays. Pressing the 

SEL

 button 

at this point enters the data and closes the program 
mode.

Program Menus

Module #1 (1-inPUt)

InP A-b – dual cnt.

CntA dP – Numeric selection depends on the 
factors determined below.

CntA SCf – This factor equals the Desired Display 
Units divided by the Number of Pulses for the 
desired display. The number varies with each meter 
and registration. Example for a W2000 DRE meter 
reading in gallons, 500.9663 pulses equals 1000 
gallons. Therefore, the factor is 1/500.9883 or 
0.0019961. To improve the accuracy the decimal 
should be moved two places and the number 
becomes 0.19961. Since the decimal was moved 
two places, the selection for Cnt dP  above is .00.

Cntb dP – (Usually the same as CntA dp.) If the units 
of measure are not the same, use the procedure 
listed above. Possible examples are gallons and 
cubic feet or cubic meters and imperial gallons.

Cntb ScF – Usually the same as CntA ScF, if not use 
the procedure listed above.

RSt P-Up – nO.

USEr InP – rESEt.

USEr Asn – both A-B.

Module #2 (2-rAte)

RAtE Enb – yES.

RAtE dP – The decimal location depends on the 
flow rate value. It typically is set to display the 
multiplier to use all six digits on the display. This 
setting is determined below.

RAtE dSP – This number represents the maximum 
flow rate to be displayed. In establishing this 
number, all 6 of the available digits should be used 
if possible. This setting is determined below.

RAtE Inp – Programs the hertz value at the 

Содержание SENSUS Act-Pak 1100D








Отзывы: