Xylem MJK SuSix, Инструкция по установке и эксплуатации

Страница: 48 / 132

48 EN 5.10 SuSix Manual 2007 FW: 841013-005/843003-001
Turbidity and Suspended Solids Transmitter
8. SuSix
®
Menus
All the
SuSix®
menus and sub menus are shown and described in the
following sections.
Continous overviews of the menu and sub-menu structures are presented
at the end of this manual:
• Main Menu Overview (page 112 )
• Converter Setup Menu Overview (page 114 )
•
Service Menu Overview
(page 122 )
• Display Setup Menu Overview (page 126 )
Main Menu
1. Press the "Setup" key on the SuSix® display (see below) to enter the
SuSix® Main Menu.
Specify Main Screen
Data Logger
Password
Set Sensor Name
Converter Setup
Display Setup
Back Select OK
Login
Activate/deactivate
Change password
Back Select OK
Set log interval
0010 sec
Back Select >
Data Logger
Set Sensor Name
SuSix1
Back Select >
Set Sensor Name
Select line
Linie 1 - Sensor name
Linie 2 - Meas.
Linie 3 -
Linie 4 -
Linie 5
Back Select OK
Specify Main Screen Converter Setup
Language
Set Clock
Modbus
Factory settings
Display SW version
Back Select OK
Display Setup
Sensor Calibration
Averaging
Units
mA output
Cleaning
Solid curve
High Alarm
Low Alarm
Sensor error
Status
Factory settings
Service Menu
Back Select OK
Select line content
Not in use
Meas.
Homogeneity
Solid curve
Clock
Back Select OK
Password
Type password
0000
Back Select >
Change password
0000
Back Select >
Activate
Deactivate
Back Select OK
Login
Activate/
Deactivate
Change password
SuSix1 [X]
Meas. FTU
Select Setup
Main Menu
Converter Top Display
SuSix1 [X]
Meas. FTU
Select Setup
Converter Top Display
Specify Main Screen
Data Logger
Password
Set Sensor Name
Converter Setup
Display Setup
Back Select OK
Main Menu
SuSix1 [X]
Prim. mg/l
Second 0.1%
Select Setup
1 - Main menus Page1
The SuSix® Main Menu contains a number of sub menus (see figure
below).
2. Press the up/down keys to highlight the required menu line
(here: Specify main screen) and then press OK to select it.
Specify Main Screen
Data Logger
Password
Set Sensor Name
Converter Setup
Display Setup
Back Select OK
Login
Activate/deactivate
Change password
Back Select OK
Set log interval
0010 sec
Back Select >
Data Logger
Set Sensor Name
SuSix1
Back Select >
Set Sensor Name
Select line
Linie 1 - Sensor name
Linie 2 - Meas.
Linie 3 -
Linie 4 -
Linie 5
Back Select OK
Specify Main Screen Converter Setup
Language
Set Clock
Modbus
Factory settings
Display SW version
Back Select OK
Display Setup
Sensor Calibration
Averaging
Units
mA output
Cleaning
Solid curve
High Alarm
Low Alarm
Sensor error
Status
Factory settings
Service Menu
Back Select OK
Select line content
Not in use
Meas.
Homogeneity
Solid curve
Clock
Back Select OK
Password
Type password
0000
Back Select >
Change password
0000
Back Select >
Activate
Deactivate
Back Select OK
Login
Activate/
Deactivate
Change password
SuSix1 [X]
Meas.
FTU
Select Setup
Main Menu
Converter Top Display
SuSix1 [X]
Meas. FTU
Select Setup
Converter Top Display
Specify Main Screen
Data Logger
Password
Set Sensor Name
Converter Setup
Display Setup
Back Select OK
Main Menu
SuSix1 [X]
Prim. mg/l
Second 0.1%
Select Setup
1 - Main menus Page1