manualshive.com logo in svg

Xylem Flygt 3201, Установка, эксплуатация и обслуживание, Страница: 46 / 48

Поделиться
Скачать
Xylem Flygt 3201 Скачать руководство пользователя страница 46

Technical reference

Application limits

Data

Description

Liquid temperature

40°C (104°F) maximum
If the pump is not equipped with cooling jacket, the pump can be operated at full

load only if at least half the stator housing is submerged.
Warm-liquid version: 90°C (195°F) maximum
At increased temperatures, the pump must be completely submerged when

operating at full load.
Ex-approved pumps: 40°C (104°F) maximum

Liquid density

1100 kg/m³ (9.2 lb per US gal) maximum

pH of the pumped media

(liquid)

5.5–14 for cast iron pumps
3–14 for stainless steel pumps

Depth of immersion

20 m (65 ft) maximum

Other

For the specific weight, current, voltage, power ratings, and speed of the pump, see

the data plate of the pump.

Motor data

Feature

Description

Motor type

Squirrel-cage induction motor

Frequency

50 or 60 Hz

Supply

1-phase or 3-phase

Starting method

• Direct on-line
• Star-delta

Maximum starts per

hour

30 evenly spaced starts per hour

Code compliance

IEC 60034-1

Rated output variation

±5%

Voltage variation without

overheating

±10%, provided that it does not run continuously at full load.

Voltage imbalance

tolerance

2%

Stator insulation class

H (180°C [360°F]).

Technical reference

44

Flygt 3201 Installation, Operation, and Maintenance Manual

Содержание Flygt 3201

















































Отзывы:

Нет отзывов