Xylem Flygt 3201 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 48

Xylem Flygt 3201 Скачать руководство пользователя страница 10

• All service and repair work is done by Xylem-authorized personnel.
• Genuine Xylem parts are used.
• Only Ex-approved spare parts and accessories authorized by Xylem are used in Ex-

approved products.

Limitations

The warranty does not cover faults caused by these situations:

• Deficient maintenance
• Improper installation
• Modifications or changes to the product and installation made without consulting

Xylem

• Incorrectly executed repair work
• Normal wear and tear

Xylem assumes no liability for these situations:

• Bodily injuries
• Material damages
• Economic losses

Warranty claim

Xylem products are high-quality products with expected reliable operation and long life.
However, should the need arise for a warranty claim, then contact your Xylem
representative.

Spare parts

Xylem guarantees that spare parts will be available for 15 years after the manufacture of
this product has been discontinued.

Introduction and Safety

8

Flygt 3201 Installation, Operation, and Maintenance Manual

«
...
8
9
10
11
12
...
»

Содержание Flygt 3201

















































Отзывы:

Нет отзывов