Xylem Flygt 3201 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 48

Xylem Flygt 3201 Скачать руководство пользователя страница 4

Remove the impeller and the wear protections ........................................................................36
Install the impeller and the wear protections.............................................................................36
Adjust the lower wear protection.................................................................................................37

Service the pump..............................................................................................................................37

Intermediate service.......................................................................................................................37
Major service...................................................................................................................................38
Service in case of alarm.................................................................................................................39

Troubleshooting...................................................................................................................................40

Introduction.......................................................................................................................................40
The pump does not start..................................................................................................................40
The pump does not stop when a level sensor is used.................................................................41
The pump starts-stops-starts in rapid sequence...........................................................................41
The pump runs but the motor protection trips.............................................................................42
The pump delivers too little or no water........................................................................................42

Technical reference.............................................................................................................................44

Application limits...............................................................................................................................44
Motor data..........................................................................................................................................44

Table of Contents

2

Flygt 3201 Installation, Operation, and Maintenance Manual

«
...
2
3
4
5
6
...
»

Содержание Flygt 3201

















































Отзывы:

Нет отзывов