Xylem Flygt 2250 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 42

background image

Do not use molybdenum disulphide (MoS

2

).

c) Grease the end of the shaft and the impeller hub.
d) Insert the key in the keyway of the shaft.
e) Fit an appropriate number of adjusting washers on the shaft.

WS001830A

2. Place the washer on the impeller screw.
3. Fit the impeller onto the shaft.
4. Tighten the impeller screw.

Tightening torque: 200 Nm (150 ft-lbs)

5. Check that the impeller can rotate easily.

WS001829A

Adjust the impeller

In order for the pump to perform at maximum capacity, the impeller must be adjusted
regularly. The impeller clearance should be minimal when the impeller is tightened. Use
the adjusting washers to adjust the clearance.
Pumps equipped with polyurethane covering are extremely resistant to wear. If the
impeller does not rotate completely freely, the friction will generate a lot of heat. This can
result in deformed wear parts, a stuck impeller, or damage to the pump. The impeller
clearance should be 0.2–0.3 mm (0.008–0.012 in.) when the impeller is tightened.

Maintenance

Flygt 2250 Installation, Operation, and Maintenance Manual

29

«
...
29
30
31
32
33
...
»

Содержание Flygt 2250











































Отзывы:

Нет отзывов

Похожие инструкции для Flygt 2250

Бренд: Makita Страницы: 96

Бренд: Nastec Страницы: 28

Бренд: Danfoss Страницы: 22

ecoTOUGH NRC111-DV-LP

Бренд: Noritz Страницы: 32

Бренд: Payne Страницы: 4

Бренд: SPX Страницы: 28

Бренд: Wayne Страницы: 4

Бренд: Panduit Страницы: 7

Бренд: Texas Equipment Страницы: 11

Бренд: SFA-SANIFLO Страницы: 14

Бренд: WACKER Group Страницы: 66

Бренд: Daikin Страницы: 44

MiniPool YC-005TB1

Бренд: W'eau Страницы: 14

Бренд: SpacePak Страницы: 48

Бренд: T.I.P. Страницы: 136

Бренд: A.O. Smith Страницы: 24

Бренд: Zenith Страницы: 8

Бренд: Wacker Neuson Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды