Xylem Flygt 2250 Скачать руководство пользователя страница 18

Страница: 18 / 42

117
85

94
98 23

19 22

110

136

WS001321A

Part

Description

Cover

Nuts

Gland nut

Figure 3: Cable entry

1. Check the data plate to see which connections are required for the power supply:

• Y

• D

• Y serial

• Y parallel

• Y/D

2. Arrange the connections on the terminal board in accordance with the required power

supply.
Do not use links (jumper strips) with the Y/D start.
Do not use links (jumper strips) with the 9 stator leads tandem-coupling.

3. Connect the motor conductors (U1, V1, W1, and earth (ground)) to the terminal board.
4. Make sure that the pump is correctly connected to earth (ground).
5. Make sure that any thermal contacts incorporated in the pump are properly connected

to the terminal board.

6. Install the cover.
7. Fasten the nuts and the gland nut on the entrance flange so that the cable insertion

assembly bottoms out.

After you have connected the motor cable to the pump, connect the motor cable and the
control cable to the starter equipment.

Installation

Flygt 2250 Installation, Operation, and Maintenance Manual

Содержание Flygt 2250











































Результаты поиска

Содержание Flygt 2250

Отзывы:

Похожие инструкции для Flygt 2250

Бренды по названию

Популярные бренды

Xylem Flygt 2250, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Flygt 2250

Отзывы:

Похожие инструкции для Flygt 2250

Бренды по названию

Популярные бренды