Xylem FLYFT P7900 Скачать руководство пользователя страница 36

Страница: 36 / 76

Labels are attached to the SUBCAB cable which is used for communication when there is

more than one SUBCAB cable. This section gives instructions for identifying which cable is

used for communication, when the label is missing.
A multimeter can be used to identify the following:

• Which signal leads are connected to the PEM
• For explosion-proof pumps: which leads are connected to the thermal contacts or

thermistors

Unused leads in the pump are isolated.

4.5.6.1 Measure the resistance

At the PEM, T1 is + and T2 is −.
1. Select a SUBCAB cable.
2. Use a multimeter to measure the resistance across T1–T2.

Measure both polarities.

T1–T2 resistance

T1–T2 resistance
Opposite polarity

Conclusion

70–130 kilohms

∞ ohm

The PEM is connected to this

cable.

∞ ohm: infinite resistance

∞ ohm

The PEM is not connected to

this cable.

3. Ex-proof pumps only: Use a multimeter to measure the resistance across T3–T4.

T3–T4 resistance

Stator temperature sensors

∞ ohm

The T3–T4 signal leads of this cable are not

used.

0–5 ohm

Thermal contacts are connected to this cable.

150–300 ohm

Thermistors are connected to this cable.

4. Repeat this process on the other cables until the signal leads which are used for

communication, have been identified.

4.5.7 Prepare the SUBCAB

™

cables

This section applies to SUBCAB

™

cables with twisted-pair control conductors.

4 Installation

P7900 Installation, Operation, and Maintenance Manual

Содержание FLYFT P7900













































































Результаты поиска

Содержание FLYFT P7900

Отзывы:

Похожие инструкции для FLYFT P7900

Бренды по названию

Популярные бренды

Xylem FLYFT P7900, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание FLYFT P7900

Отзывы:

Похожие инструкции для FLYFT P7900

Бренды по названию

Популярные бренды