Xylem FLYFT P7900 Скачать руководство пользователя страница 46

Страница: 46 / 76

5 Operation

5.1 Precautions

Before taking the unit into operation, check the following:

• All recommended safety devices are installed.
• The cable and cable entry have not been damaged.
• All debris and waste material has been removed.

NOTICE:
Never operate the pump with the discharge line blocked, or the discharge valve closed.

WARNING: Crush Hazard
Risk of automatic restart.

Distance to wet areas

WARNING: Electrical Hazard
Risk of electrical shock or burn. You must connect an additional ground- (earth-) fault

protection device to the grounded (earthed) connectors if persons are likely to come into

contact with liquids that are also in contact with the pump or pumped liquid.

CAUTION: Electrical Hazard
Risk of electrical shock or burn. The equipment manufacturer has not evaluated this unit for

use in swimming pools. If used in connection with swimming pools then special safety

regulations apply.

5.2 Noise level

In certain installations and at certain operating points on the pump performance curve, the

sound pressure level can exceed 70 dB(A). Pumps with power output greater than 30 kW, as

shown in the diagram below, may have a sound pressure level between 70 dB(A) and

maximum 85 dB(A) at the best efficiency point.
Make sure that you understand the noise level requirements in the environment where the

product is installed. Failure to do so may result in hearing loss or violation of local laws.

dB(A)

65
60
55

1000

100

WS006231A

Figure 19: Sound pressure

5 Operation

P7900 Installation, Operation, and Maintenance Manual

Содержание FLYFT P7900













































































Результаты поиска

Содержание FLYFT P7900

Отзывы:

Похожие инструкции для FLYFT P7900

Бренды по названию

Популярные бренды

Xylem FLYFT P7900, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание FLYFT P7900

Отзывы:

Похожие инструкции для FLYFT P7900

Бренды по названию

Популярные бренды