background image

2.

 

Decrease Value button will decrease the speed of the blower (motor) from 4 to 1 (strongest to 
quietest). Increase Value button will increase the speed of the blower (motor) from 1 to 4 
(quietest to strongest).   

              Touch Power button once to turn off the system.   

Note: The system saves user configurations, settings such as light, timer and blower (motor) speed will re-

main the same the next time it is turned on. 

 
B. To turn the light on: 

1.

 

Touch Light button once to turn on the lights, and once again to turn off the lights. 

C. Adjusting the timer function:   

1.

 

While the blower (motor) is not running, touch and hold Decrease Value button over 3 
seconds to enter timer mode.   

2.

 

Adjust to desired period of delay off timer by touching Increase Value or Decrease Value 
button (minimum 1 minute to maximum 15 minutes). This setting will be saved immediately.   

 
D. Activating the timer function:   

1.

 

While the blower (motor) is running, touch and hold Power button for over 3 seconds to activate 
delay off timer. Power-off delay indicator will lit up and power-off delay digital timer will begin to 
countdown, when it reaches zero, the blower (motor) will shut down. 

 
E. To clear cleaning reminder: 

 

When blower (motor) starts to rotate, cumulative running time will be shown in 

Power-On 

Elapsed Digital Timer

. This timer icon flashes when 30 hours is up and reminds user to clean 

the baffle filters.   

 

After cleaning the filters and when the motor is not in use, touch and hold (+) 

Increase Value 

button over 3 seconds to reset the timer. Please note that turning off the system will not reset 
the 

Power-On Elapsed Digital Timer

.  

 

F. AUTOMATIC SHUT OFF: 
 

 

MACHINE WILL AUTOMATICLY SHUT OFF AFTER OF APP. 2 ½ HOURS (FOR THOSE MANUFACTURED 
AFTER AUGUST 2012 ONLY) 

 

SPECIFICATION: 

Body Design   

Non-Magnetic 1.0 mm Stainless Steel, Satin Finish   

Power Rating   

120V/60Hz (USA & Canada standard) 

General Input Power   

154W (150W + 2x2W) 

Motor Input Power   

150 W each 

Ampere  

1.3 A 

Levels Of Speed Control 

4 Levels 

Maximum Airflow 

900CFM 

Noise Level 

Approximately 0.7 Sone(35dB)    to 6.5 Sone (67dB) (Lowest to Highest Speed) 

Number Of Motors   

Single Motor 

Motor Type   

Single Chamber Ultra Quiet 

Fan Type   

Squirrel Cage 

Filtration Type   

Heavy Duty Stainless Steel Baffle Filter 

Illumination   

LED light, 2W Maximum 

Venting Size   

  Top 8 inches Round 

Interference Protection   

Radio Frequency Interference Protected 

Note 

Specification subject to change without notice, contact your local reseller for details. 
 

 

www.XtremeAirUsa.com

                                                                    PAGE 

10

 

 

Содержание PRO-X PX01-I36













Отзывы: