manualshive.com logo in svg

Xtreme Power Conversion XPRT 6/10KVA, Руководство пользователя и инструкция по установке

Поделиться
Скачать
Xtreme Power Conversion XPRT 6/10KVA Скачать руководство пользователя страница 5

XPRT-6kVA, XPRT-10kVA USER’S MANUAL  

 

UNINTERRUPTIBLE POWER SUPPLY (UPS) 

 
Xtreme Power Conversion® (XPC) Corporation (Rev 2/7/13) 

 

 

 

 

Page 5 

 

LEDs ......................................................................................................................................................... 79 

Features .................................................................................................................................................. 79 

Architecture ............................................................................................................................................ 80 

Installation .............................................................................................................................................. 81 

Interfaces ............................................................................................................................................ 82 

Configuration ...................................................................................................................................... 82 

Access .................................................................................................................................................. 85 

 

INTRODUCTION 

Thank you for selecting this uninterruptible power supply (UPS). It provides you with protection for 
connected equipment. 

Please read this manual

 before installing the XPRT-Series UPS models XPRT-6000 

and XPRT-10000 as it provides important information that should be followed during installation and 
maintenance of the UPS and batteries, allowing you to correctly set up your system for the maximum 
safety and performance. Included is information on customer support and service, if it is required. If you 
experience a problem with the UPS, please refer to the Troubleshooting section in this manual to correct 
the problem. If the problem is not corrected, please collect information so that the Technical Support 
personnel can more effectively assist you. 

EMC Statements - FCC Part 15 

Notice: 

This equipment has been tested and found to comply with the limits for a Class A digital device, 

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against 
harmful interference when the equipment is operated in a commercial environment. This equipment 
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with 
the instruction manual, may cause harmful interference to radio communications. Operation of this 
equipment in a residential area is likely to cause harmful interference in which case the user will be 
required to correct the interference at the users own expense. 

Modifications not expressly approved by the manufacturer could void the user’s authority to operate the 
equipment under FCC rules.  

Содержание XPRT 6/10KVA






















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды