background image

TOOLS NEEDED - 

(FOR HANGING)

Adjustable

WRENCH

LEVEL

LADDER

OVERVIEW

Thank you for purchasing the XTRASUN DE Double-Ended 1000W Open Lighting System. This 

system is engineered to provide ultra-wide, uniform, efficient light delivery over the growing area.

For information on additional Xtrasun products please visit Hydrofarm.com.

WARNING: FAILURE TO FOLLOW OUR GUIDELINES COULD RESULT IN ELECTRICAL SHOCK.

 

Do not touch, move, spray, or clean your light fixture when it is plugged in. Allow it to cool down be-

fore handling. Recommended mounting clearance for your fixture is 8

-12

 on all sides. Do not mount 

directly to any surface. Make sure to disconnect the power when changing the lamp. 

XTRASUN DE SERIES BALLAST ELECTRICAL SPECIFICATIONS

Model Watts

Main 

Voltage

Operating 

Voltage 

Range

Max 

Input 

Power

Output Power Settings

Power 

Factor

Ignitor 

Voltage THD

CF

ta

tc

XTDE1TH 1000W

240V

216-264V 1200W 600W-750W-825W-1000W-1150W > 0.99

4 kV

<10%

<1.7

40°C/104°F 75°C/167°F

Model

BALLAST INPUT AMPERAGE REFERENCE

XTDE1TH

Imax 240V

1150W 240V

1000W 240V

825W 240V

750W 240V

600W 240V

5.06A

5.06A

4.60A

3.91A

3.48A

2.86A

2

Содержание XTDEOKT1









Отзывы: