Xtrails VESDA-E VEP-A00 Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 109

background image

VESDA-E VEP-A00-P Product Guide

36

www.xtralis.com

4.3.6

Relays

The relays, located on the main processor card, interface to the Fire Alarm Control Panel (FACP) to
communicate faults, alarms and disabled states. The relays can be programmed using Xtralis VSC. Relays 3
and 6 are permanently set for Urgent Fault and Fire 1 respectively. Table 4-22 below illustrates the default
assignments of functions (conditions) to relays and summarizes the default behavior of each relay. Section
5.5.9 describes how to configure the relay behavior using Xtralis VSC. It is possible to assign more than one
condition to a relay.

Fire 1 Relay

If a detector relay is to be used to signal fire alarm to the Fire Alarm Control Panel (FACP) then the Fire 1 relay
must be used.

Fault and Fire 1 Relay Terminals

The Urgent and Minor Fault relays are energized during normal operation while the Fire 1 relay is only
energized when a Fire 1 is detected. The operation of the relays are summarized in the following table.

Table 4-1: Typical Relay Operation

URGENT FAULT Relay

All Other Relays

No Fault

(Energized)

Fault

or unpowered state

No Fire

(De-energized)

Fire

Relay Assignments and Behaviour

l

Relays 1, 2, 4, 5 and 7 are fully configurable. For example, Relay 5 could be configured to de-energize on
Alert

l

Relays 3 and 6 are fixed to Urgent Fault and Fire 1 respectively. These relays may be assigned additional
conditions.

Relay #

Default

Assignment

Default to

Normally

Energized

Description for default configuration

Configurability

1

Disable

(Isolate) and

Standby

No

Energizes when an operator disables
(isolates) the detector. Also energizes when
the operator puts the detector into Standby
mode.

Fully

configurable

2

Minor Fault

Yes

De-energizes when a Minor Fault is
detected.

Fully

configurable

3

Urgent Fault,

Disable,

Standy

Yes

De-energizes when an Urgent Fault is
detected or when Disable or Standby
occurs.

Note that Relay 3 is fixed Normally
Energized in order to ensure that a fault will
be signaled when power to the VEP-A00 is
removed. See Table 4-1.

Urgent Fault

cannot be

removed. Other

conditions can

be added.

Fixed Normally

Energized

4

Alert

No

Energizes when the Alert alarm is initiated.

Fully

configurable

Table 4-2: Default Relay Assignments

«
...
42
43
44
45
46
...
»

Содержание VESDA-E VEP-A00














































































































Отзывы:

Нет отзывов

Похожие инструкции для VESDA-E VEP-A00

Бренд: Ultra Start Страницы: 4

Бренд: Ultra Start Страницы: 4

Бренд: AstroStart Страницы: 20

Protek Wireless IW-101A

Бренд: Innotek Страницы: 4

Бренд: Clifford Страницы: 25

Бренд: LST Страницы: 2

Бренд: stabo Страницы: 12

Бренд: Argus Страницы: 4

Бренд: ELITA Страницы: 2

Бренд: Sharper Image Страницы: 28

Бренд: Eurochron Страницы: 8

Бренд: Kingdun Electronic Страницы: 10

Бренд: System Sensor Страницы: 12

Бренд: Radio Shack Страницы: 4

Бренд: olympia electronics Страницы: 2

Бренд: BEARWARE Страницы: 34

Бренд: BROWIN Страницы: 75

Бренд: Radio Shack Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды