Xtrails VESDA-E VEP-A00 Скачать руководство пользователя страница 6

Страница: 6 / 109

VESDA-E VEP-A00-P Product Guide

www.xtralis.com

Regional Regulatory Requirements and Notices

European Installations

EN 54-20

The product must use a power source conforming to EN 54-4 and EN60950-1 Section 2.5.

The product is compliant with EN 54-20 sensitivity requirements provided the following conditions are met:

For a Class A detector, hole sensitivity must be better than 1.5% obscuration/m and transport time less
than 60 seconds

For a Class B detector, hole sensitivity must be better than 3% obscuration/m and transport time less
than 90 seconds

For a Class C detector, hole sensitivity must be better than 8% obscuration/m and transport time less
than 110 seconds

These limits should be verified using ASPIRE during the design of the sampling pipe network.

The product is compliant with EN 54-20 flow monitoring requirements provided the following conditions are
met:

The minor low and minor high flow thresholds should be set at 85% and 115% respectively

The flow through the detector predicted by ASPIRE must be greater than 20 L/m.

Additional information:

The VESDA-E VEP-A00 passed the EN 54-20 fire tests with the following configurations:

Class A with 40 holes and a Fire-1 setting of 0.028% obs/m

Class B with 80 holes and a Fire-1 setting of 0.027% obs/m

Class C with 100 holes and a Fire-1 setting of 0.072% obs/m

Only applies to VEP-A00-P.

Japanese Installations

To comply with Japanese local code requirements the WiFi capability shall be disabled.

Product Listings

ULC

ActivFire

VdS

EN 54-20

ISO 7240-20

Regional approvals listings and regulatory compliance vary between product models. Refer to www.xtralis.com for
the latest product approvals matrix.

Document:

22060_1

Part Number: AD30274-000

Содержание VESDA-E VEP-A00














































































































Результаты поиска

Содержание VESDA-E VEP-A00

Отзывы:

Похожие инструкции для VESDA-E VEP-A00

Бренды по названию

Популярные бренды

Xtrails VESDA-E VEP-A00, Руководство по эксплуатации продукта

Результаты поиска

Содержание VESDA-E VEP-A00

Отзывы:

Похожие инструкции для VESDA-E VEP-A00

Бренды по названию

Популярные бренды