Xtrails VESDA-E VEP-A00 Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 109

background image

VESDA-E VEP-A00-P Product Guide

58

www.xtralis.com

5.5.4

Smoke Threshold Options

The Smoke Threshold options provide the mechanism to set the smoke obscuration trigger point for each
alarm level, and the ability to assign day or night thresholds to cater for different levels of activity in the
protected area during these times.

Refer to Section 5.6 for the default settings.

Figure 5-14: Smoke Threshold Options

The Smoke Threshold configuration options are as follows:

l

Day Thresholds:

The settings for day time smoke thresholds. The threshold and the delay are used

together to decide when to trigger the alarm condition.

l

Night Thresholds:

The settings for night time smoke thresholds. The threshold and the delay are used

together to decide when to trigger the alarm condition.

l

Delay:

The length of time between the alarm threshold being reached and the relay operation

l

Cumulative Delay:

If checked the delay timer for each alarm condition will not start until both the

smoke level has exceeded the threshold and the delay timer for the previous alarm condition has
expired. If not checked the delay timer for each alarm condition will start immediately when the
smoke level exceeds the threshold.

l

Instant Fire:

If checked, the Fire 1 time delay is ignored when the smoke exceeds the Fire 1

threshold before the Alert and Action conditions have occurred.

l

Significant Smoke Change - Logging:

The smoke change level at which an event is recorded in the

Event Log.

l

Significant Smoke Change - VESDAnet:

The smoke change level at which a smoke status update is

output on VESDAnet.

l

Changeover:

l

Work Days:

Select which days use both day and night thresholds. Night time thresholds are used if

a day is not selected.

l

Day / Night Changeover Time:

The settings for the timing of the threshold changeover.

l

Holidays:

The settings used to define a holiday period. Use the dropdown calendars to choose the

start and end times of the holiday (or break) period. Night time thresholds are used during the holiday
period.

«
...
64
65
66
67
68
...
»

Содержание VESDA-E VEP-A00














































































































Отзывы:

Нет отзывов

Похожие инструкции для VESDA-E VEP-A00

Бренд: LEXIBOOK Страницы: 9

K-SMOKE-42-R-PW

Бренд: Kalamazoo Страницы: 64

Бренд: La Crosse Technology Страницы: 6

Бренд: ZAZU Страницы: 8

Бренд: stabo Страницы: 12

Бренд: Audiovox Страницы: 21

Бренд: Directed Electronics Страницы: 37

Бренд: Kidde Страницы: 13

Бренд: Kidde Страницы: 17

Бренд: KREAFUNK Страницы: 46

Бренд: Disney Страницы: 2

Бренд: Paradox Страницы: 4

Бренд: CrimeStopper Страницы: 1

Бренд: IKEA Страницы: 8

Бренд: Fire-Lite Страницы: 2

Бренд: Fire-Lite Страницы: 2

Ungo Pro Security SR9000

Бренд: Clarion Страницы: 53

Бренд: A.I.&.E Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды