Xstream X-HW13008GEN Скачать руководство пользователя страница 37

Страница: 37 / 40

SYMPTOM

PROBABLE CAUSE

REMEDY

Burner runs erratically.

Water in the fuel oil.

Drain fuel filter/water separator.

Drain fuel tank, and replace with

clean fuel.

Dirty fuel filter/water

separator.

Replace element.

Dirty fuel nozzle.

Replace.

Fuel pickup screen

obstructed.

Consult Customer Service.

Improper air adjustment

setting.

Adjust as explained on page 26.

Fuel pump malfunctioning.

Replace.

Burner runs, but will

not heat.

Poor or improper fuel

supply.

Check fuel to ensure it is correct.

Drain tank and replace filter if

necessary and refill with proper

fuel.

Low fuel pump pressure.

Check fuel pump pressure,

adjust or replace if needed.

Dirty fuel nozzle.

Replace.

Fuel pickup screen

obstructed.

Consult Customer Service.

Improper air adjustment

setting.

Adjust as explained on page 26.

Scale build up in heat

exchanger coil.

Consult your Customer Service.

Burner discharges

white smoke.

Low on fuel.

Refuel. If white smoke persists,

consult Customer Service.

Poor or improper fuel

supply.

Check fuel pump pressure,

adjust or replace if needed.

Dirty fuel nozzle.

Replace.

Fuel pickup screen

obstructed.

Consult Customer Service.

Improper air adjustment

setting.

Adjust as explained on page 26.

Cold combustion chamber

start-up.

Run burner for several minutes.

Excessive air supply.

Adjust as explained on page 26.

Burner discharges

black smoke.

Insufficient air supply.

Adjust as explained on page 26.

Combustion chamber

loaded with unburned fuel.

Consult Customer Service.

troubleshooting

Содержание X-HW13008GEN









































Результаты поиска

Содержание X-HW13008GEN

Отзывы:

Бренды по названию

Популярные бренды

Xstream X-HW13008GEN, Руководство по эксплуатации

Результаты поиска

Содержание X-HW13008GEN

Отзывы:

Бренды по названию

Популярные бренды