Xstream X-HW13008GEN, Руководство по эксплуатации

Страница: 20 / 40

20
DANGER
DO NOT SMOKE WHILE FUELING!
DO NOT FILL THE FUEL TANK WHILE UNIT IS
RUNNING OR HOT. ALLOW UNIT TO COOL FOR
TWO MINUTES BEFORE RE-FUELING.
DO NOT FILL FUEL TANK TO POINT OF
OVERFLOWING. ALLOW APPROXIMATELY 1/4” OF
TANK SPACE FOR FUEL EXPANSION.
ALWAYS STORE FUEL AWAY FROM THE WASHER
WHILE THE UNIT IS RUNNING OR HOT.
BURNER FUEl TANK
1. Review “Risk of Explosion or Fire” pg. 8, before fueling.
2. Locate the Safety Decals on your unit and heed their warnings.
3. Fill the burner fuel tank with good quality, clean No. 1 or No. 2 fuel oil
diesel or kerosene. Do not use gasoline!
ADJUSTABlE PRESSURE DUAl lANCE
This unit features an Adjustable Pressure Dual Lance which allows the
user to select a high or low pressure “fan” spray. Simply rotate the adjust-
able grip on the dual lance to achieve the desired pressure selection.
1. Selection of high pressure can be achieved by turning the adjustable
grip on the Dual Lance assembly counterclockwise as shown in the
figure below.
2. Selection of low pressure can be achieved by turning the adjustable
grip on the Dual Lance clockwise as shown in the figure below.
installation & preparation
WARNING
THE TRIGGER GUN SHOULD ALWAYS BE LOCKED IN THE OFF
POSITION WHEN NOT IN USE! NEVER LOOK DIRECTLY AT THE
NOZZLE UNLESS IT IS DISCONNECTED FROM THE TRIGGER
GUN/DUAL LANCE ASSEMBLY!
4 Operator's Manual
installation & preparation
adJustable pressure dual lance:
This unit features an Adjustable Pressure Dual Lance which allows the user to
select a high or low pressure “fan” spray. Simply rotate the adjustable grip on
the dual lance to achieve the desired pressure selection.
. Selection of high pressure can be achieved by turning the adjustable grip on
the Dual Lance assembly counterclockwise as shown in the figure below .
2. Selection of low pressure can be achieved by turning the adjustable grip on
the Dual Lance clockwise as shown in the figure below.
dual lance connection:
. Be certain the trigger gun is locked in the “OFF” position.
2. Connect the dual lance assembly to the trigger gun assembly at this time
(if applicable). Be certain the connection is securely tightened.
water supply:
. Select a water supply hose which is a quality grade of garden hose measuring
at least 3/4” ID and no longer than 50 feet.
2. If your unit is equipped with a water strainer, ensure it is clean and free of
any obstructions. Periodic cleaning of the water strainer will help prevent
pump problems. As a strainer becomes obstructed, it restricts proper flow of
water to the pump. This can result in cavitation which will cause premature
failure of pump packings.
a. Unscrew the strainer bowl from the unit.
b. Remove strainer screen and clean or replace.
3. Connect one end of the water supply hose to the water inlet of the unit.
Connect the other end of the hose to your pressurized water supply.
NOTE: If there is a high mineral content in your water, it is recommended that a
water softener be used to prevent the possibility of excessive scale buildup
inside the heat exchanger coil.
4. Follow the incoming water requirements listed below:
a. Water pressure must be between a minimum of 20 pounds per square
inch (PSI) and a maximum of 25 PSI.
b. Incoming GPM must be approximately one gallon more than the outgoing
GPM stated on the pressure washer nameplate. (You can check GPM by
timing how long it takes to fill a 5 gallon container.)
c. Incoming water temperature must not exceed 25°F. Excessive pump
damage may result if the water temperature exceeds this acceptable
level.
5. Never allow the unit to operate without the incoming water line attached and
the water supply completely turned on.
WARNING
risK of inJection causing
seVere inJury!
-tHe trigger gun sHould
always be locKed in tHe off
position wHen not in use!
-neVer looK directly at
tHe noZZle unless it is
disconnected from tHe
trigger gun/dual lance
assembly!