Xray T4'21 Скачать руководство пользователя

Страница: 23 / 48

ECS DRIVE SHAFT

MAINTENANCE

VIDEO TECH TIP

▶

BEARING ECS DRIVE

SHAFTS

VIDEO TECH TIP

▶

901302

SB M3x2.5

305392

P 2x10

305394

P 2x9

902205

SH M2x5

940510

BB 5x10x4

980210

P 2x10

Use Alu 50mm Drive Shafts in rear

OIL

BEARING OIL

(HUDY #106230)

THREAD LOCK

GRAPHITE GREASE

(HUDY #106210)

2x10mm

2x9mm

GRAPHITE GREASE

(HUDY #106210)

DO NOT OVERTIGHTEN

REAR TRANSMISSION

FRONT TRANSMISSION

L=R

#305242

DRIVE SHAFT REPLACEMENT CAP

3.5MM ORANGE - STRONG (4)

DETAIL STEP

Set-screw against the flat spot.

Set-screw against

the flat spot.

5. FRONT & REAR TRANSMISSION

L=R

0° OUTBOARD TOE-IN UPRIGHTS

Left UPRIGHT = Right UPRIGHT

Longer drive shafts (52mm) make the car easier to drive because they give more traction and better stability, mainly in chicanes.

However, the car will understeer more than with shorter (50mm) shafts which give a lot of steering and make the car more aggressive.

Both left & right shafts should ALWAYS be the same length at one end of the car (front or rear).

52mm

shafts are recommended for

carpet high-traction

tracks.

51mm

shafts are recommended for

carpet

tracks and

large asphalt

tracks.

50mm

shafts are recommended for

low-traction

tight asphalt

tracks.

DRIVE SHAFTS

#305323 50MM - STEEL
#305324 52MM - STEEL
#305326 52MM - ALU
#305334 51MM - ECS
#305333 50MM - ECS

UPRIGHTS

#303352 0° 2-HOLE MEDIUM OPTION
#303354 0° 2-HOLE HARD

INCLUDED

#303360 0° 2-HOLE GRAPHITE OPTION

The optional ECS ball-bearing driveshafts feature a new ball-bearing assembly

at the inner end of the driveshaft where it inserts into the outdrive. They offer

a significant performance improvement over the standard blade-type driveshafts.

The friction between the driveshaft and the outdrive is greatly reduced, which gives

much smoother handling especially on fast direction changes such as chicanes. The

reduced friction also helps to increase cornering speeds. The new ball-bearing

driveshafts must be used with optional

#305138 SOLID AXLE ECS BB DRIVESHAFT

ADAPTERS

We recommend the shorter 52mm shafts for smaller, more technical tracks, where

more initial steering is needed.

The 53mm shafts are best suited for more open and flowing track layouts. They will

provide slightly less initial steering, but better steering in the middle of the corner,

as well as on power.

#305308 ECS BB DRIVE SHAFT 52mm - SET

#305309 ECS BB DRIVE SHAFT 53mm - SET

TIP

For easy installation of the

#305241 plastic caps, use pliers

as shown.

The CVD bearing driveshafts improve off-power steering and rotation, but decrease

rear traction and stability. Recommended for use in high-traction conditions, and for

tracks with many hairpin corners.

The new ball-bearing driveshafts must be used with optional:

#304972 GEAR DIFF CVD BB DRIVESHAFT OUTDRIVES

#305409

CVD BB DRIVE SHAFT 50mm - SET - HUDY Spring Steel™

#305409

#304972

#305308

#305309

#305138

Содержание T4'21

















































Результаты поиска

Содержание T4'21

Отзывы:

Похожие инструкции для T4'21

Бренды по названию

Популярные бренды

Xray T4'21, Инструкция по эксплуатации

Результаты поиска

Содержание T4'21

Отзывы:

Похожие инструкции для T4'21

Бренды по названию

Популярные бренды