XLT Ovens 1832 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 94

background image

Technical Support US: 888-443-2751

Technical Support INTL: 316-943-2751

33

OVEN SERVICE PROCEDURES

Invertek VFD (World) Programming Procedure

Read the entire instruction before programming.

TIP

Programming Instructions For Factory Parameters

1.  Press and hold NAVIGATE > 2 seconds.
2.  Press UP Arrow until (P-14) is displayed and press NAVIGATE.
3.  Press UP Arrow until (201) is displayed and press NAVIGATE to save and return to parameter

menu.

4.  Press UP Arrow until (P-15) is displayed and press NAVIGATE.
5.  Press UP Arrow until (2) is displayed and press NAVIGATE to save and return to parameter menu.
6.  Press UP Arrow until (P-17) is displayed and press NAVIGATE.
7.  Press UP Arrow until (24) is displayed and press NAVIGATE to save and return to parameter

menu.

8. Press UP Arrow until (P-20) is displayed and press NAVIGATE.
9. Press DOWN Arrow until (0.0) is displayed and press NAVIGATE to save and return to parameter

menu.

10. Press UP Arrow until (P-21) is displayed and press NAVIGATE.
11. Press UP Arrow until (60.0) is displayed and press NAVIGATE to save and return to parameter

menu.

12. Press UP Arrow until (P-51) is displayed and press NAVIGATE.
13. Press UP Arrow until (1) is displayed and press NAVIGATE to save and return to parameter menu.

14. Press DOWN Arrow until (P-38) is displayed and press NAVIGATE.
15. Press UP Arrow until (1) is displayed and press NAVIGATE to save and return to parameter menu.
16. Press and hold NAVIGATE > 2 seconds to return to operating display.

With the Oven Control switched off and power connected to the oven, the VFD should show
“Stop” on the display.

Do Not Exceed 65 Hz On VFD Settings.

START

When in keypad mode, used to Start a stopped
drive or to reverse the direction of rotation if bi
-directional keypad mode is enabled.

UP

Used to increase speed in real-time mode or to
increase parameter values in parameter edit
mode.

DOWN

Used to decrease speed in real-time mode or to
decrease parameter values in parameter edit
mode.

NAVIGATE

Used to display real-time information, to ac-
cess and exit parameter edit mode and to store
parameter changes.

RESET/STOP

Used to reset a tripped drive.
When in Keypad mode, used to Stop a running
drive.

«
...
31
32
33
34
35
...
»

Содержание 1832































































































Отзывы:

Нет отзывов

Похожие инструкции для 1832

Бренд: Panasonic Страницы: 109

Бренд: Cadco Страницы: 47

Бренд: Candy Страницы: 36

Бренд: Daewoo Страницы: 23

Бренд: DAEWOO ELECTRONICS Страницы: 27

Бренд: Parmco Страницы: 27

Бренд: DeLonghi Страницы: 13

Бренд: Danby Страницы: 77

Бренд: Nordson ASYMTEK Страницы: 125

Бренд: Jenn-Air Страницы: 15

Бренд: Caple Страницы: 28

Бренд: Electrolux Страницы: 36

Бренд: Electrolux Страницы: 12

Бренд: Electrolux Страницы: 28

Бренд: Electrolux Страницы: 8

Бренд: Electrolux Страницы: 8

Бренд: Electrolux Страницы: 48

Бренд: Electrolux Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды