manualshive.com logo in svg

XLT Ovens 1832, Руководство по запчастям и обслуживанию

Поделиться
Скачать
XLT Ovens 1832 Скачать руководство пользователя страница 27

Technical Support  US:  888-443-2751 

Technical Support  INTL:  316-943-2751 

 

27 

OVEN TROUBLESHOOTING 

LUI Service Error Codes 

Display Alarm

MC LED

Error Determination

Troubleshooting

Oven Probe

Alarm LED on. Flash HEAT 
LED. All other LED's operate 
as normal.

Temp Sensor Error, Open or Short. 
Temp <40F (4C) or >700F (371C)

Perform A Hard Reset. If Error Still Exists, 
Contact XLT.

PCB Temp Probe

Alarm LED on. Flash HEAT 
LED. All other LED's operate 
as normal.

Temp Sensor Error, Open or Short. 

Perform A Hard Reset. If Error Still Exists, 
Contact XLT.

Ignition Error

Alarm LED on. Flash HEAT 
LED. All other LED's operate 
as normal.

From Ignition enable (run) signal, if 
oven doesn’t see 25F (-4C) temp 
rise in three (3) minuites. If restart 
(actual temp within 50F (10C) of set 
point) error timing ten (10) minutes.

Check To See If Gas Hose Is Connected. 
Next, Is Exterior Gas Valve On? If Yes, 
Perform A Hard Reset. If No, Turn Gas 
Valve On. If Error Still Exists, Contact XLT.

Over Temp

Alarm LED on. Flash HEAT 
LED. All other LED's operate 
as normal.

Temp is 50F (10C) over set point 
for period > one (1) minute. If user 
adjusts set point lower, inhibit alarm 
until new set point is reached.

Perform A Hard Reset. If Error Still Exists, 
Contact XLT.

Under Temp

Alarm LED on. Flash HEAT 
LED. All other LED's operate 
as normal.

Once set point is reached, the Actual 
is 15F (-9C) under set point for 
more than thirty (30) minutes. If user 
adjusts set point, reset timer. 

Check To See If Gas Hose Is Connected. 
Next, Is Exterior Gas Valve On? If Yes, 
Perform A Hard Reset. If Error Still Exists, 
Contact XLT.

Over Speed

Alarm LED on. Flash 
CONVEYOR LED. All other 
LED's operate as normal.

Speed > thirty (30) seconds fast 
Duration vs. Set Point

Perform A Hard Reset. If Error Still Exists, 
Check LUI Settings. If Settings Are Correct, 
Perform A Pan Test To Confirm Settings. If 
Error Still Exists, Contact XLT.

Under Speed

Alarm LED on. Flash 
CONVEYOR LED. All other 
LED's operate as normal.

Speed > thirty (30) seconds slow 
Duration vs. Set Point

Check Drive Chain and Sprocket To Verify 
Proper Working Condition. Perform A Hard 
Reset. If Error Still Exists, Check LUI 
Settings. If Settings Are Correct, Perform A 
Pan Test To Confirm Settings. If Error Still 
Exists, Contact XLT.

Software Error

Alarm LED flash. All other 
LEDs off.

Internal Software Error

Check for pinched wires. Perform A Hard 
Reset. If Error Still Exists, Contact XLT.

EEPROM Error

Alarm LED flash. All other 
LEDs off.

Bad Checksum

Perform A Hard Reset. If Error Still Exists, 
Contact XLT.

Key Short

Alarm LED flash. All other 
LEDs off.

Any Key Shorted > one (1) minute.

Clean LUI Screen. Perform A Hard Reset.If 
Error Still Exists, Contact XLT.

Comm Error

Alarm LED flash. All other 
LEDs off.

Internal Software Error

Perform A Hard Reset. If Error Still Exists, 
Contact XLT.

Hi Alarm

Alarm LED on. Flash HEAT 
LED. All other LED's operate 
as normal.

Hi Alarm set point exceeded.

Perform A Hard Reset. If Error Still Exists, 
Contact XLT.

Main Fan Low 

Amps

Alarm LED on. Flash FAN 
LED. All other LED's operate 
as normal.

Amps below min level per Main Fan 
Amp level table for ten (10) seconds.

Perform A Hard Reset. If Error Still Exists, 
Contact XLT.

Main Fan High 

Amps

Alarm LED on. Flash FAN 
LED. All other LED's operate 
as normal.

Amps above max level per Main Fan 
Amp level table for ten (10) seconds.

Check CB1 To See If It Has Tripped. If Yes, 
Reset CB1. If No, Perform A Hard Reset. If 
Error Still Exists, Contact XLT.

Belt Jam

Conveyor LED flash. All other 
LED's operate as normal.

If the current motor speed is less 
than 25% of the most recent 
minimum motor speed.

Check For Obstructions. If No Obstructions 
Are Found, Check Drive Chain and Sprocket 
To Verify Proper Working Condition. 
Perform A Hard Reset. If Error Still Exists, 
Contact XLT.

Содержание 1832































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды