Xilinx Zynq-7000 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 50

Xilinx Zynq-7000 Скачать руководство пользователя страница 38

Chapter 3:

Getting Started with the Base Targeted Reference Design

38

ZC702 and ZVIK Getting Started Guide

UG926 (v6.0) December 17, 2013

• External video (available with the optional ZVIK FMC module)

°

The input video is supplied by an external video source and is connected through

the FMC-IMAGEON card.

Sobel Filter Modes are explained as follows:

Sobel OFF

• No processing done. Sobel filter is bypassed.

Sobel – SW

• Video processing (edge-detection filter) done by software code running on PS

Sobel On – HW

• Video processing (edge-detection filter) done by PL

shows the detected image edges of the video generated by the TPG, that is,

case 1 versus case 2 or 3 of

.

3. Enter

0

to exit the application and return to the command prompt.

Running the Video Demonstration for 720p Video
Resolution

Configure the display monitor to 720p60 resolution: 1280 x 720p @ 60 Hz. If using the ZVIK

with an external video source, configure the external video source to 1280 x 720 @ 60 Hz.

• Follow these steps for running QT based GUI demonstration application in 720p mode:

a. Exit any previously running applications.
b. Type these commands at the Linux command prompt into the host PC based

terminal:

zynq>

run_sobel.sh -qt -res 1280x720

• Follow the steps for running UART Menu based Demonstration Application in 720p

mode:
a. Exit any previously running applications.
b. Type these commands at the Linux command prompt into the host PC based

terminal:

zynq>

run_sobel.sh -cmd -res 1280x720

«
...
36
37
38
39
40
...
»

Содержание Zynq-7000



















































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды