manualshive.com logo in svg

Xilinx Zynq-7000, Руководство по началу работы

Поделиться
Скачать
Xilinx Zynq-7000 Скачать руководство пользователя страница 36

Chapter 3: 

Getting Started with the Base Targeted Reference Design

36

www.xilinx.com

ZC702 and ZVIK Getting Started Guide

UG926 (v6.0) December 17, 2013

While exercising the modes described above, one can observe AXI bus bandwidth utilization 

and CPU utilization on the graphs in the Qt GUI application.

8. Click 

Exit

 to quit the application and return the user to Linux console.

9. The application can be restarted by typing the following at the Linux command prompt:

zynq> 

run_sobel.sh -qt -res 1920x1080

Running the UART Menu-Based Demonstration 

Application

A command line based Linux application demonstration is also provided with the package. 

This application presents the user with a command line menu-based UI to exercise different 

modes of the video demonstration.

To run the menu-based UI application demonstration, the Qt-based GUI application which 

was started (as explained in 

Running the Qt-Based GUI Application Demonstration, page 32

) 

needs to be quit as per 

step 8, page 36

.

The following steps explain how to start the UART menu-based application demonstration 

and exercise different application video use cases.

1. Go to the UART terminal started on your host PC as explained in 

step 2

 from 

Running the 

Qt-Based GUI Application Demonstration, page 32

.

X-Ref Target - Figure 3-8

Figure 3-8: 

Images with Sobel Filter On (Left) and with Sobel Filter Off (Right)

UG926_c3_08_041113

Send Feedback

Содержание Zynq-7000



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды