manualshive.com logo in svg

Xilinx ML505, Руководство пользователя

Поделиться
Скачать
Xilinx ML505 Скачать руководство пользователя страница 44

44

www.xilinx.com

ML505/ML506/ML507 Evaluation Platform

UG347 (v3.1.1) October 7, 2009

Chapter 1:

ML505/ML506/ML507 Evaluation Platform

R

41. Serial-ATA Host Connectors

Serial-ATA (SATA) is the next generation of the ATA interface used for storage devices 
such as hard disks. The board contains two SATA host connectors that can be connected to 
a SATA device (such as a hard disk) using a standard SATA cable. The SATA connectors 
are connected to GTPs on the FPGA as shown in 

Table 1-26

.

SATA can also be used as a convenient and low cost medium for connecting GTP/GTX 
transceivers. The SATA physical interface can carry GTP/GTX signals up to 1.5 Gb/s for 
general-purpose usage. The board ships with a special Xilinx SATA crossover cable that is 
used as a loopback connection between the two SATA host connectors for loopback testing 
and bit error rate testing (BERT). The SATA crossover cable can also be used to connect 
GTP/GTX transceivers between two boards. For GTP/GTX SATA clock jumpering, see 

Figure 1-4, page 32

.

Note:

The special SATA crossover cable cannot be used to connect a SATA host to a SATA device 

(that is, PC to hard disk). It is only intended for host-to-host loopback connections.

42. SFP Connector

The board contains a small form-factor pluggable (SFP) connector and cage assembly that 
accepts SFP modules. The SFP interface is connected to GTP0 of GTP_X0Y4 on the FPGA. 
The SFP module serial ID interface is connected to the IIC multiplexer on the board (See 

“14. IIC Bus with 8-Kb EEPROM,” page 27

 for more information). The control and status 

signals for the SFP module are connected to jumpers, test points, and LEDs as described in 

Table 1-27

. The SFP module connections are shown in 

Table 1-28, page 45

.

Table 1-26:

SATA Connections

Pin Name

FPGA Pin (U1)

Connector Pin

ML505/ML506

ML507

SATA1_RX_P

W1

J40, pin 6

GTP0 of 
GTP_X0Y2 
receive pair

GTX0 of 
GTX_X0Y3 
receive pair

SATA1_RX_N

Y1

J40, pin 5

SATA1_TX_P

V2

J40, pin 2

GTP0 of 
GTP_X0Y2 
transmit pair

GTX0 of 
GTX_X0Y3 
transmit pair

SATA1_TX_N

W2

J40, pin 3

SATA2_RX_P

AB1

J41, pin 6

GTP1 of 
GTP_X0Y2 
receive pair

GTX1 of 
GTX_X0Y3 
receive pair

SATA2_RX_N

AA1

J41, pin 5

SATA2_TX_P

AC2

J41, pin 2

GTP1 of 
GTP_X0Y2 
transmit pair

GTX1 of 
GTX_X0Y3 
transmit pair

SATA2_TX_N

AB2

J41, pin 3

Downloaded from 

Elcodis.com

 

electronic components distributor

 

Содержание ML505





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды