manualshive.com logo in svg

Xilinx ML505, Руководство пользователя

Поделиться
Скачать
Xilinx ML505 Скачать руководство пользователя страница 18

18

www.xilinx.com

ML505/ML506/ML507 Evaluation Platform

UG347 (v3.1.1) October 7, 2009

Chapter 1:

ML505/ML506/ML507 Evaluation Platform

R

Digitally Controlled Impedance

Some FPGA banks can support the digitally controlled impedance (DCI) feature in 
Virtex-5 FPGAs. Support for DCI is summarized in 

Table 1-2

.

2. DDR2 SODIMM

The ML50

x

 platform is shipped with a single-rank unregistered 256 MB SODIMM. The 

DDR2 SODIMM used is generally a Micron MT4HTF3264HY-53E or similar module. Serial 
Presence Detect (SPD) using an IIC interface to the DDR DIMM is also supported with the 
FPGA.

Note:

The board is only tested for DDR2 SDRAM operation at a 400 MHz data rate. Faster data 

rates might be possible but are not tested.

MIG Compliance

The ML50

x

 DDR2 interface is MIG pinout compliant. The MIG DDR2 routing guidelines 

outlined in the 

Xilinx Memory Interface Generator (MIG) User Guide

 

[Ref 17]

 have been 

achieved.

The board’s DDR2 SODIMM memory interface is designed to the requirements defined by 
the 

MIG User Guide

 using the MIG tool. The MIG documentation requires that designers 

follow the MIG pinout and layout guidelines. The MIG tool generates and ensures that the 
proper FPGA I/O pin selections are made in support of the board’s DDR2 interface. The 
initial pin selection for the board was modified and then re-verified to meet the MIG 
pinout requirements. To ensure a robust interface, the ML50

x

 DDR2 layout incorporates 

matched trace lengths for data signals to the corresponding data strobe signal as defined in 
the MIG user guide. See 

Appendix C, “References”

 for links to additional information 

about MIG and Virtex-5 FPGAs in general.

Table 1-2:

DCI Capability of FPGA Bank

FPGA Bank

DCI Capability

1

Not supported

2

Not supported

3

Not supported

4

Not supported

11

Yes, 49.9

Ω

 resistors are installed

12

Not supported

13

Yes, 49.9

Ω

 resistors are installed

14

Yes, 49.9

Ω

 resistors are installed

15

Yes, 49.9

Ω

 resistors are installed

16

Yes, 49.9

Ω

 resistors are installed

17

Yes, 49.9

Ω

 resistors are installed

18

Not supported

21

Yes, 49.9

Ω

 resistors are installed

Downloaded from 

Elcodis.com

 

electronic components distributor

 

Содержание ML505





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды