manualshive.com logo in svg

Xilinx ML505, Руководство пользователя

Поделиться
Скачать
Xilinx ML505 Скачать руководство пользователя страница 33

ML505/ML506/ML507 Evaluation Platform

www.xilinx.com

33

UG347 (v3.1.1) October 7, 2009

Detailed Description

R

The Platform Flash PROM can program the FPGA by using the master or slave 
configuration in serial or parallel (SelectMap) modes. The Platform Flash PROM is 
programmed using Xilinx iMPACT software through the board’s JTAG chain. See the 

“Configuration Options,” page 53

 section for more information.

24. JTAG Configuration Port

The JTAG configuration port for the board (J1) allows for device programming and FPGA 
debug. The JTAG port supports the Xilinx Parallel Cable III, Parallel Cable IV, or Platform 
USB cable products. Third-party configuration products might also be available. The JTAG 
chain can also be extended to an expansion board by setting jumper J21 accordingly. See 
the 

“Configuration Options,” page 53

 section for more information.

25. Onboard Power Supplies

Power supply circuitry on the board generates 0.9V, 1.0V, 1.8V, 2.5V, and 3.3V voltages to 
power the components on the board. The 1.0V, 1.8V, and 3.3V supplies are driven by Texas 
Instruments PTH08T2 switching power regulators. These regulators are driven with a 
400 kHz clock so they run synchronous to each other, reducing noise caused by beat 
frequencies. The clocks sent to each regulator are also out of phase to reduce reflected noise 
at the input. In addition, the board utilizes the regulators’ 

turbo trans

 feature to improve 

output transient response.

The diagram in 

Figure 1-5, page 34

 shows the power supply architecture and maximum 

current handling on each supply. The typical operating currents are significantly below the 
maximum capable. The board is normally shipped with a 15W power supply, which 
should be sufficient for most applications.

Downloaded from 

Elcodis.com

 

electronic components distributor

 

Содержание ML505





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды