manualshive.com logo in svg

Xilinx ML505, Руководство пользователя

Поделиться
Скачать
Xilinx ML505 Скачать руководство пользователя страница 32

32

www.xilinx.com

ML505/ML506/ML507 Evaluation Platform

UG347 (v3.1.1) October 7, 2009

Chapter 1:

ML505/ML506/ML507 Evaluation Platform

R

Jumpers J22, J23, and J24 allow the user to select the default interface that the PHY uses 
(

Figure 1-4

 and 

Table 1-16

). The interface can also be changed via MDIO commands.

22. USB Controller with Host and Peripheral Ports

A Cypress CY7C67300 embedded USB host controller provides USB connectivity for the 
board. The USB controller supports host and peripheral modes of operation. The USB 
controller has two serial interface engines (SIE) that can be used independently. SIE1 is 
connected to the USB Host connector (P18). SIE2 is connected only to the USB Peripheral 
connector (P17).

The USB controller has an internal microprocessor to assist in processing USB commands. 
The firmware for this processor can be stored in its own dedicated IIC EEPROM (U28) or 
can be downloaded from a host computer via a peripheral connector. The USB controller's 
serial port is connected to J30 through an RS-232 transceiver to assist with debug. Jumper 
J50 can be installed to prevent the USB controller from executing firmware stored in the IIC 
EEPROM.

23. Xilinx XCF32P Platform Flash PROM Configuration Storage Devices

The two onboard Xilinx XCF32P Platform Flash PROM configuration storage devices offer 
a convenient and easy-to-use configuration solution for the FPGA. The Platform Flash 
PROM holds up to two separate configuration images (up to four with compression) that 
can be accessed through the configuration address switches. To use the Platform Flash 
PROM to configure the FPGA, the configuration DIP switch must be set to the correct 
position.

Figure 1-4:

PHY Jumpers on the Board

J22

J23

GMII/MII to copper

J24

J22

J23

SGMII to copper; no clock

J24

J22

J23

RGMII; modified MII in copper

Note:

 J56 = SATA Clock Select

J24

J56

J56

J56

UG347_05_112706

Table 1-16:

PHY Default Interface Mode

Mode

Jumper Settings

J22

J23

J24

GMII/MII to copper 

(default)

Jumper over pins 1-2

Jumper over pins 1-2

No jumper

SGMII to copper, 

no clock

Jumper over pins 2-3

Jumper over pins 2-3

No jumper

RGMII

Jumper over pins 1-2

No jumper

Jumper on

Downloaded from 

Elcodis.com

 

electronic components distributor

 

Содержание ML505





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды