5/2011
2-27
Phaser 4600/4620 Printer Service Manual
07-320-00, 07-330-00, 07-331-00
Status Indicator RAPS
Revision - Xerox Internal Use Only
07-320-00 Tray 4 is Open RAP
07-320-00 The Tray 4 Size Switch indicates Tray 4 is open.
BSD-Reference:
WD 13
Initial Actions
1.
Close the Tray.
2.
Check the Size Switch.
Procedure
WARNING
Switch off the electricity to the machine. Disconnect the power cord from the customer
supply while performing tasks that do not need electricity. Electricity can cause death or
injury. Moving parts can cause injury.
Cycle system power. The error message is displayed.
Y
N
Complete.
Remove Tray 4 and inspect the Size Switch. The Size Switch is undamaged.
Y
N
Replace the Size Switch,
REP 7.30
, then retest.
Select
dC330
code 07-400 to test the switch. The switch signal changes (open/closed).
Y
N
Remove the Right Cover (
REP 28.2
) and reseat CN5 on the Feeder Board, then retest.
The sensor signal changes.
Y
N
Replace the Feeder Board,
REP 7.28
.
Reassemble and perform
SCP 6
Final Actions.
Replace these components in order until the error is corrected.
1.
Size Switch,
PL 8.30 Item 9
2.
Feeder Board,
PL 8.30 Item 7
3.
MCU Board,
PL 3.10 Item 3
07-330-00, 07-331-00 Jam in Tray 4 RAP
07-330-00 Jam 0 in Tray 4. Media remains in the Tray 4 Pick-up Assembly.
07-331-00 Check Tray 4 Feed Area. Media remains at the Tray 4 Take Away Sensor.
BSD-Reference:
WD 13
Initial Actions
1.
Check for obstructions in the media path.
Procedure
WARNING
Switch off the electricity to the machine. Disconnect the power cord from the customer
supply while performing tasks that do not need electricity. Electricity can cause death or
injury. Moving parts can cause injury.
Check the Nudger, Feed, and Separator Rollers for excessive wear or contamination. The
rollers are undamaged and clean.
Y
N
Clean or replace the rollers.
Check for obstructions or debris in the media path. The media path is clear.
Y
N
Clear the media path of obstructions or debris.
Check Tray 3 Pick Assembly (
PL 8.20 Item 17
) motion. Pick assembly motion is good.
Y
N
Repair improper pick assembly motion.
Select
dC330
code 08-840 to test the Feed Clutch. The clutch is engaged (on/off).
Y
N
Remove the Right Cover (
REP 7.25
) and reseat CN9 on the Feeder Board, then retest.
The clutch is engaged.
Y
N
Replace the Feed Clutch,
REP 8.41
.
Reassemble and perform
SCP 6
Final Actions.
Select
dC330
code 08-940 to test the Feed Drive. The Feed Drive Assembly rotates (on/
off).
Y
N
Remove the Right Cover (
REP 7.25
) and reseat CN7 on the Feeder Board, then retest.
The Feed Drive Assembly rotates.
Y
N
Replace the Feed Drive Assembly,
REP 8.42
.
Reassemble and perform
SCP 6
Final Actions.
Replace these components in order until the error is corrected.
1.
Feed Assembly,
PL 8.40 Item 10
Содержание Phaser 4600
