Xerox DocuPrint 2065 Скачать руководство пользователя страница 35

Страница: 35 / 240

2.1 Main Components and Functions

Front cover release lever

Pulled towards you to open the front cover when replacing the print cartridge or
clearing paper jams.

Output tray

Delivers printed output face down.

Extension output tray

Extended to prevent output from falling off the output tray.

No.

Name

Description

Right/Rear View

No.

Name

Description

Rear cover

Removed when installing the optional hard disk, memory card, or ROM.

Ventilation hole

Releases heat to prevent the interior of the printer from overheating.

Important

• Locking the ventilation hole causes heat build-up in the printer, which causes

the printer to malfunction.

USB connector

Connects a USB cable to the printer.

Parallel connector

Connects a parallel cable to the printer.

Network connector

Connects a network cable to the printer. A network cable is used when
connecting the printer to a network.

Tray covers

The rear covers for the paper trays.

Power cord connector

Connects a power cord to the printer.

Circuit breaker

Cuts off the power circuit automatically in the event of current leakage.

Slot for PostScript
ROM or font ROM

Connector for
hard disk

Slot for memory card

Controller board with the rear cover and metal plate cover open

Connector for

network expansion card

Содержание DocuPrint 2065
















































































































































































































































Результаты поиска

Содержание DocuPrint 2065

Отзывы:

Похожие инструкции для DocuPrint 2065

Бренды по названию

Популярные бренды

Xerox DocuPrint 2065, Руководство пользователя

Результаты поиска

Содержание DocuPrint 2065

Отзывы:

Похожие инструкции для DocuPrint 2065

Бренды по названию

Популярные бренды