Xerox DocuPrint 100 EPS Скачать руководство пользователя страница 143

Страница: 143 / 158

Operator Guide

5- 41

Troubleshooting

Troubleshooting the 36-track tape drive

Use the following procedures to solve problems with your 36-track
tape drive:

•

Performing basic recovery

•

Troubleshooting initial program load (IPL) failure

•

Handling problems with inserting a tape cartridge

•

Troubleshooting tape unload problem

•

Unload a cartridge after a power failure

•

Troubleshooting tape winding completely out of cartridge

•

Troubleshooting blank message display

•

Troubleshooting tape drive ready problem

•

Calling for service

Performing basic recovery

Always try to recover the cartridge from the inch cartridge tape
drive before you try to correct any problems with the drive. Follow
these basic recovery steps:

1. Take the tape drive offline.

2. If there is a relevant message on the display monitor or

controller, perform the action described there.

3. If there is an error code on the tape drive message display,

record the error code and time, then call for service.

Troubleshooting initial program load (IPL) failure

An error occurred during the IPL procedure if:

•

The three indicator lights (Read only, Ready, and Mode) flash
on the 36-track drive.

•

An error code displays after you power on the tape drive.

Содержание DocuPrint 100 EPS































































































































































Результаты поиска

Содержание DocuPrint 100 EPS

Отзывы:

Похожие инструкции для DocuPrint 100 EPS

Бренды по названию

Популярные бренды

Xerox DocuPrint 100 EPS, Руководство оператора

Результаты поиска

Содержание DocuPrint 100 EPS

Отзывы:

Похожие инструкции для DocuPrint 100 EPS

Бренды по названию

Популярные бренды