background image

5 - 4

Operator Guide

Troubleshooting

Ensure that a valid PDL is used; for example, an Adobe driver 
outputs a valid PDL file in PostScript format.

NOTE: Gray scales or graphic images may contain image quality 
differences if they are printed using a 300 dpi decomposer.

Isolating and resolving printer-driven print quality problems

Problem: The output from the printer contains defects such as 
deletions, line problems, and missing images.

Determine if the job has ever been printed correctly on this 
system.

If possible, print the job on a draft printer. If the job prints 
correctly, contact the customer support center.

Determine if other jobs are exhibiting the same problem. This 
could indicate a printer problem. Contact the customer support 
center.

Recreate the job with a different print driver and resubmit it to 
the printer.

Resolving font problems

Use the following procedures to isolate and resolve common font 
problems.

Problem:  The job prints with the wrong font.

Determine if the font is being downloaded with the job. If a 
downloaded font is not found, font substitution occurs and an 
error page is printed.

If the font is not being downloaded with the job, determine if 
the font is loaded on the server by viewing the PostScript/PCL 
Fonts tab on the Administration window.

Problem:  Characters appear jagged.

Determine if there is a scalable option available for that font 
and whether the user selected that option.

Problem:  Some incorrect characters print.

Determine if the document was created with one driver and 
printed with another driver.

Problem:  Text runs off the page, or sentences run into each 
other.

Determine if the document was created with one driver and 
printed with another driver.

Problem:  Small fonts are printing ragged.

Change the default font renderer in the Printer Manager from 
Adobe Type Manager to Font Solution.

Содержание DocuPrint 100 EPS































































































































































Отзывы: