manualshive.com logo in svg

Xerox 3117 - Phaser B/W Laser Printer, Руководство по обслуживанию

Поделиться
Скачать
Xerox 3117 - Phaser B/W Laser Printer Скачать руководство пользователя страница 84

x

Service Manual

Troubleshooting

6-10

6.3.6  Cover Open

• Description

The ERROR lamp is on even when the print cover is closed.

Check and Cause

Solution

1. The Hook Lever in the top cover may be defective.

2. Check the connector (Engine B’d

↔

HVPS) and circuit of

the cover switch department in the Main Control board.
Perform DCU mode : If Error state '64' occurs, Check the
related codes of the Cover Open Error.

1. Replace the hook lever, if defective. 

2. Check the insertion of the Cover Open S/W

Connect.

3. Replace the Main Control board or Cover Open

S/W. 

6.3.7  No lamp on when the cover is open

• Description

The ERROR lamp does not come on even when the printer cover is open

Check and Cause

Solution

1. Check the connector and circuit of the cover switch

department in the Main Control board. Perform DCU
mode : If Error state '64' occurs, Check the related codes
of the Cover Open Error

1. Check the insertion of the Cover Open S/W

Connect.

2. Replace the Main Control board or Cover Open

S/W. 

Содержание 3117 - Phaser B/W Laser Printer


































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды