Xerox 3117 - Phaser B/W Laser Printer Скачать руководство пользователя страница 60

Страница: 60 / 129

Service Manual

Alignment and Adjustments

4-16

4.7.5 Tips for Avoiding Paper Jams

By selecting the correct paper types, most paper jams can be avoided.

• Ensure that the adjustable guides are positioned correctly.

• Do not overload the tray.

• Do not remove the paper from the tray while printing.

• Flex, fan and straighten the paper before loading.

• Do not use creased, damp or highly curled paper.

• Do not mix paper types in the input tray.

• Use only recommended print media.

• Ensure that the recommended print side is facing up when loading paper into the input tray.

4.7.6 Solving Print Quality Problems

Print Quality Checklist

Print quality problems can be resolved by following the checklist below.

• Redistribute toner in the toner cartridge

• Clean the inside of the printer

• Adjust the print resolution from the printer properties

• Ensure that the Toner Save mode is off

• Clear general printing problems

• Install a new toner cartridge, and check the print quality

Содержание 3117 - Phaser B/W Laser Printer


































































































































Результаты поиска

Содержание 3117 - Phaser B/W Laser Printer

Отзывы:

Бренды по названию

Популярные бренды

Xerox 3117 - Phaser B/W Laser Printer, Руководство по обслуживанию

Результаты поиска

Содержание 3117 - Phaser B/W Laser Printer

Отзывы:

Бренды по названию

Популярные бренды