Xerox 3117 - Phaser B/W Laser Printer Скачать руководство пользователя страница 42

Страница: 42 / 129

System Overview

Service Manual

3-29

4. Pay attention not to overload paper. Paper overloading may cause paper jams.

5. If necessary, pinch the rear guide to adjust for the paper length and pinch the side guide and slide it to

the left flush against the paper.

3.4.4 Connecting a Printer Cable

To print from your computer, you need to connect your printer to your computer with a Universal Serial Bus (USB)

cable.

1. Make sure that both the printer and the computer are turned off.

2. Plug the USB printer cable into the connector on the back of the printer.

3. Connect the other end of the cable to the USB port on your computer.

See your computer User’s Guide if you need help.

Содержание 3117 - Phaser B/W Laser Printer


































































































































Результаты поиска

Содержание 3117 - Phaser B/W Laser Printer

Отзывы:

Бренды по названию

Популярные бренды

Xerox 3117 - Phaser B/W Laser Printer, Руководство по обслуживанию

Результаты поиска

Содержание 3117 - Phaser B/W Laser Printer

Отзывы:

Бренды по названию

Популярные бренды