Xero88 CHILLI 12 x 10 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 30

background image

User Interface

Chilli Dimmer 73-853-00 Issue 8

Page 29 of 30

Alarm Input

The Chilli Dimmer has an alarm
input,

which

when

activated,

causes it to enter an alarm state.

If  the  dimmer  is  networked,  it  will
also  send  out  alarm  messages  to
ensure  that  all  other  devices  on
the  network  also  enter  the  alarm
state.

Alarm Input Active

When the dimmer’s Alarm Input is
activated, the following will occur:

• The dimmer enters the Alarm

State.

• All channel output levels fade

to 80% over a period of 1s (see
note).

• All menu access via the control

panel is disabled.

• The screen shows:

DIMMER LOCKED

* ALARM ACTIVE *

• If the dimmer is in Network

Mode it sends out an Alarm On
message.

• The Alarm On message is

repeated  every  5  seconds
while  the  Alarm  Input  remains
active.

Alarm Input Inactive

When  the  dimmer’s  Alarm  Input
changes  from  active  to  inactive,
the following will occur:

• The dimmer exits the Alarm

State.

• All output channels fade to

their normal levels over a
period of 1s.

• All menu access via the control

panel is enabled.

• The screen shows the main

screen.

• If the dimmer is in Network

Mode it sends out an Alarm Off
message.

Alarm On Message

When

a

networked

dimmer

receives an Alarm On message,
the following will occur:

• The dimmer enters the Alarm

State.

• All channel output levels fade

to 80% over a period of 1s (see
note).

• All menu access via the control

panel is disabled.

• The screen shows:

DIMMER LOCKED

* ALARM ACTIVE *

Alarm Off Message

When

a

networked

dimmer

receives  an  Alarm  Off  message
and  its  Alarm  Input  is  not  active,
the following will occur:

• The dimmer exits the Alarm

State.

• All output channels fade to

their normal levels over a
period of 1s.

• All menu access via the control

panel is enabled.

• The screen shows the main

screen.

Notes

Alarm State - Output Levels

When  the  dimmer  is  in  the  Alarm
State, the output levels are subject
to  topset,  but  not  temperature
shutdown.  Manual  control  levels,
memories,  sequences,  preheat
and  DMX  inputs  do  not  have  any
contribution  to  the  final  output
levels.

Alarm State on Power Up

On  power  up,  the  alarm  state  of
the  dimmer  is  determined  by  the
alarm  input  only,  ie  it  does  not
remember  any  alarm  messages
previously received.

«
...
27
28
29
30
»

Содержание CHILLI 12 x 10































Отзывы:

Нет отзывов

Похожие инструкции для CHILLI 12 x 10

Бренд: Stiga Страницы: 387

Бренд: Katana Страницы: 8

Бренд: ATIKA Страницы: 143

Бренд: Okay Страницы: 32

Бренд: Cramer Страницы: 151

Бренд: DeWalt Страницы: 52

Бренд: DeWalt Страницы: 168

Бренд: DeWalt Страницы: 44

Бренд: DeWalt Страницы: 56

Бренд: DeWalt Страницы: 48

Бренд: DeWalt Страницы: 52

Бренд: DeWalt Страницы: 52

Бренд: DeWalt Страницы: 176

Бренд: DeWalt Страницы: 164

Бренд: DeWalt Страницы: 40

Бренд: RUSTA Страницы: 84

Бренд: PLP Страницы: 28

Бренд: F&F Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды